How to remove and install a Brake Master Cylinder on Volkswagen Jetta?

Firstly, precautions have to be taken because brake fluid may harm paint or finished surfaces to remove the master cylinder. The master cylinder cannot be serviced, and therefore change it in case it is faulty. Start by unscrewing the engine cover and unplugging the cable of the negative battery terminal. Then take off the battery and battery tray, unscrew electrical connectors of brake fluid level warning switch and brake light switch. Aspirate the reservoir as much as possible and in manual transaxle models unscrew and use a plug to remove the vacuum on the master cylinder hose of the clutch. Unscrew the brake light mounting fastener and switch, then use careful caution to pull the locking tabs on the reservoir outward then raise it off the master cylinder. Clean the surroundings on the fittings of the brake line, remove the brake lines, and seal up all holes to avoid contamination. Unscrew the mounting nuts of the master cylinder and the master cylinder and heat shield of the power booster. In case of installing a new master cylinder, new seals are to be employed when transfers the reservoir. To install, bench bleed the new master cylinder, and connect bleeder tubes to each outlet port and pour the suggested amount of brake fluid into the reservoir. Put the pistons slowly into the master cylinder to push the air out until there are no more bubbles. Take the bleed tubes out and replace them with plugs in the vacant ports and place the reservoir cap. Install the power brake booster with the studs on the master cylinder by screwing in the nuts with fingers and installing the brake line fittings into the master cylinder. Fix the mounting nuts and fittings of the brake lines tightly. In the case of manual transaxle models, attach the hose of the clutch master cylinder. Dump the master cylinder reservoir into the fluid, then bleed the master cylinder and brake system by having an assistant press the brake pedal and loosen the fitting so that air and fluid could escape. Repeat until no air bubbles are left in the fluid and be sure to have rags ready to slop any fluid. When bleeding is finished, wash the place beneath master cylinder thoroughly with clean water and make sure that the brake system is working properly and then resume regular service of the vehicle.

Genuine Volkswagen Jetta Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Brake Master Cylinders found

View related parts
Volkswagen Jetta Master Cylinder Part Number: 5QM-614-019-G
$55.98 MSRP: $77.75
You Save: $21.77 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2019-2024 Volkswagen Jetta | GLI Autobahn, GLI S, R-Line, S, SE, SEL, SEL Premium, Sport | 4 Cyl 1.4 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 5QM-614-019-C
$87.45 MSRP: $122.48
You Save: $35.03 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2019 Volkswagen Jetta | GLI 35th Anniversary Edition, GLI Autobahn, GLI S, R-Line, S, SE, SEL, SEL Premium | 4 Cyl 1.4 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1J1-614-019-A
$217.77 MSRP: $305.00
You Save: $87.23 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2001 Volkswagen Jetta | GL, GLS, GLX, TDI, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 5QM-614-019-H
$35.53 MSRP: $59.22
You Save: $23.69 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2019-2024 Volkswagen Jetta | GLI 35th Anniversary Edition, GLI Autobahn, GLI S, R-Line, S, SE, SEL, SEL Premium, Sport | 4 Cyl 1.4 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1J1-614-019-F
$262.59 MSRP: $358.73
You Save: $96.14 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Replaces: 1J1-614-019-C
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2001-2005 Volkswagen Jetta | GL, GL TDI, GLI, GLS, GLS TDI, GLX, TDI, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 357-611-019-B
$250.34 MSRP: $342.00
You Save: $91.66 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Replaces: 1H1-611-019-B
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1991-1999 Volkswagen Jetta | Celebration Edition, City, GL, GLI 16-Valve, GLS, GLX, GT, Jazz, K2, Limited Edition, TDI, Trek, Wolfsburg Edition | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1K1-614-019-AG
$272.19 MSRP: $371.86
You Save: $99.67 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder; Brake Booster, Master Cylinder
- Replaces: 1K1-614-019-N, 1K1-614-019-AA, 1K1-614-019-S
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2012-2013 Volkswagen Jetta | S, SE, SEL | 5 Cyl 2.5 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1J1-614-019-K
$285.00 MSRP: $389.36
You Save: $104.36 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1999-2005 Volkswagen Jetta | GL, GL TDI, GLI, GLS, GLS TDI, GLX, TDI, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1K1-614-019-AF
$294.62 MSRP: $402.49
You Save: $107.87 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder; Master Cylinder
- Replaces: 1K1-614-019-R, 1K1-614-019-T, 1K1-614-019-M, 1K1-614-019-C, 1K1-614-019-G
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2005-2018 Volkswagen Jetta | 2.0T, 2.5, Base, GL, GL TDI, GLI, GLI SE, GLI SEL, GLS, GLS TDI, S, SE, SE Sport, SEL, SEL Premium, Sport, TDI, TDI Cup Edition, TDI Premium, TDI S, TDI SE, TDI SEL, Value Edition, Wolfsburg Edition | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS, 5 Cyl 2.5 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1H1-698-019-B
$284.02 MSRP: $388.00
You Save: $103.98 (27%)
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1993-1999 Volkswagen Jetta | Celebration Edition, City, GL, GLS, GT, Jazz, K2, Limited Edition, TDI, Trek, Wolfsburg Edition | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 3A1-698-019
$284.02 MSRP: $388.00
You Save: $103.98 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1994-1999 Volkswagen Jetta | GLX | 6 Cyl 2.8 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1K1-614-019-AB
$336.24 MSRP: $459.34
You Save: $123.10 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Replaces: 1K1-614-019-Q
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2013-2016 Volkswagen Jetta | Hybrid, Hybrid SE, Hybrid SEL, Hybrid SEL Premium | 4 Cyl 1.4 L FULL HYBRID EV-GAS (FHEV)
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1H1-698-019-A
$365.41 MSRP: $499.20
You Save: $133.79 (27%)
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1994-1995 Volkswagen Jetta | GLS | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 191-611-019
$211.63 MSRP: $296.40
You Save: $84.77 (29%)
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1984-1989 Volkswagen Jetta | Base, Carat, GL, GLI, GLI 16-Valve, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.7 L GAS, 4 Cyl 1.8 L GAS
View related parts
Volkswagen Jetta Master Cylinder Part Number: 1H1-611-019-C
$218.96 MSRP: $306.67
You Save: $87.71 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder
- Replaces: 357-611-019
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1990-1992 Volkswagen Jetta | Carat, GL, GLI 16-Valve | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS

Volkswagen Jetta Brake Master Cylinder

Choose OEM Brake Master Cylinder for superior quality and long-lasting durability. They match the Volkswagen's factory specifications exactly and pass strict quality control. If you plan to replace Brake Master Cylinder on your Jetta, put OEM at the top of your list. You'll get the right fit, reliable performance, and peace of mind. We stock an extensive inventory of genuine Volkswagen Jetta parts. It is easy to find what you need. You will love our competitive prices that help you save. No more hassle with returns or guesswork. Every part includes a warranty straight from the manufacturer. Get trusted quality, strong durability, and real value today.

Volkswagen Jetta Brake Master Cylinder Parts and Q&A

Master Cylinder
1K1-614-019-AB
Q: How to remove and install a Brake Master Cylinder on Volkswagen Jetta?
A:
Firstly, precautions have to be taken because brake fluid may harm paint or finished surfaces to remove the master cylinder. The master cylinder cannot be serviced, and therefore change it in case it is faulty. Start by unscrewing the engine cover and unplugging the cable of the negative battery terminal. Then take off the battery and battery tray, unscrew electrical connectors of brake fluid level warning switch and brake light switch. Aspirate the reservoir as much as possible and in manual transaxle models unscrew and use a plug to remove the vacuum on the master cylinder hose of the clutch. Unscrew the brake light mounting fastener and switch, then use careful caution to pull the locking tabs on the reservoir outward then raise it off the master cylinder. Clean the surroundings on the fittings of the brake line, remove the brake lines, and seal up all holes to avoid contamination. Unscrew the mounting nuts of the master cylinder and the master cylinder and heat shield of the power booster. In case of installing a new master cylinder, new seals are to be employed when transfers the reservoir. To install, bench bleed the new master cylinder, and connect bleeder tubes to each outlet port and pour the suggested amount of brake fluid into the reservoir. Put the pistons slowly into the master cylinder to push the air out until there are no more bubbles. Take the bleed tubes out and replace them with plugs in the vacant ports and place the reservoir cap. Install the power Brake Booster with the studs on the master cylinder by screwing in the nuts with fingers and installing the brake line fittings into the master cylinder. Fix the mounting nuts and fittings of the brake lines tightly. In the case of manual transaxle models, attach the hose of the clutch master cylinder. Dump the master cylinder reservoir into the fluid, then bleed the master cylinder and brake system by having an assistant press the brake pedal and loosen the fitting so that air and fluid could escape. Repeat until no air bubbles are left in the fluid and be sure to have rags ready to slop any fluid. When bleeding is finished, wash the place beneath master cylinder thoroughly with clean water and make sure that the brake system is working properly and then resume regular service of the vehicle.