How to remove and install the Air Temperature Sensor and MAP Sensor on Volkswagen Jetta?

The process is used on all engines other than 2.0L turbocharged CBFA and CCTA engines, the MAP sensor is positioned on the intake manifold and it is near the throttle body. The Intake Air Temperature (IAT) sensor goes hand in hand with the MAP sensor and is referred to as Intake Manifle Sensor. Start by taking away the engine cover. In the case of 1.4L engines, the air filter housing is to be taken out. The second step is to find and unconnect the electrical connector of the MAP/IAT sensor. Unclip the MAP sensor off the manifold or loosen the mounting fasteners wherever possible but take care not to lose the O-ring because there is no replacement part, a new sensor is supplied. Installation is a backward process of removal.

How is the MAP Sensor accessed in the charge air intake duct on Volkswagen Jetta?

The sensor is located in the charge air intake duct. For 1.8L and 2.0L CPLA, CPPA, CPKA, and CPRA engines, the air filter housing assembly must be removed to access the sensor. For all other 1.8L and 2.0L engines, the front of the vehicle should be raised and supported on jackstands, followed by the removal of the engine undercover. Once located, the electrical connector should be disconnected. The sensor fasteners need to be removed or the tabs released, allowing for the sensor to be taken out of the duct. The O-ring should be discarded, and a new one must be used during the installation of the same sensor, which is done in reverse order of removal.

Genuine Volkswagen Jetta MAP Sensor

Manifold Air Pressure Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 MAP Sensors found

View related parts
Volkswagen Jetta Sensor Part Number: 076-906-051-A
$85.67 MSRP: $119.98
You Save: $34.31 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 03G-906-051-A
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2009 Volkswagen Jetta | TDI | 4 Cyl 2.0 L DIESEL
View related parts
Volkswagen Jetta Map Sensor Part Number: 06L-906-052
$95.19 MSRP: $133.32
You Save: $38.13 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Press Sensor; Map Sensor, Pressure Sensor
- Replaced by: 06L-906-052-A
- Replaces: 06K-906-052, 06E-906-052
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2012-2023, 2009-2010 Volkswagen Jetta | GLI, GLI 35th Anniversary Edition, GLI Autobahn, GLI S, GLI SE, GLI SEL, R-Line, S, SE, SEL, SEL Premium, Wolfsburg Edition | 4 Cyl 1.4 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Pressure Sensor Part Number: 07C-906-051
$99.95 MSRP: $139.99
You Save: $40.04 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Press Sensor
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2011-2013 Volkswagen Jetta | S, SE, SEL | 5 Cyl 2.5 L GAS
View related parts
Volkswagen Jetta Map Sensor Part Number: 04E-906-051
$102.33 MSRP: $143.32
You Save: $40.99 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Press Sensor; Map Sensor
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2013-2021 Volkswagen Jetta | Hybrid, Hybrid SE, Hybrid SEL, Hybrid SEL Premium, R-Line, S, SE, SEL, SEL Premium, Wolfsburg Edition | 4 Cyl 1.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.4 L GAS
View related parts
Volkswagen Jetta Pressure Sensor Part Number: 03L-906-051-D
$157.07 MSRP: $219.98
You Save: $62.91 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor; Pressure Sensor
- Replaces: 03L-906-051-B
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2015 Volkswagen Jetta | Base, GLI SE, GLI SEL, Hybrid SEL Premium, S, SE, SEL, Sport, TDI S, TDI SE, TDI SEL | 4 Cyl 1.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Pressure Sensor Part Number: 07K-906-051-B
$135.65 MSRP: $189.98
You Save: $54.33 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Press Sensor
- Replaces: 07K-906-051
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2012-2013 Volkswagen Jetta | S, SE, SEL | 5 Cyl 2.5 L GAS
View related parts
Volkswagen Jetta Pressure Sensor Part Number: 036-906-051-G
$92.81 MSRP: $129.99
You Save: $37.18 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Press Sensor; Pressure Sensor
- Replaced by: 03C-906-051-F
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2005-2008 Volkswagen Jetta | 2.5, S, SE, SEL, Value Edition, Wolfsburg Edition | 5 Cyl 2.5 L GAS
View related parts
Volkswagen Jetta Map Sensor Part Number: 05E-906-051-L
$45.95 MSRP: $63.82
You Save: $17.87 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Press Sensor
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2022-2023 Volkswagen Jetta | S, SE, SEL, Sport | 4 Cyl 1.5 L GAS
View related parts
Volkswagen Jetta Map Sensor Part Number: 07L-907-386-B
$122.56 MSRP: $171.64
You Save: $49.08 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor; Position Sensor
- Replaces: 07L-907-386-A, 07L-907-386
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2011-2018 Volkswagen Jetta | Base, GLI, GLI SE, GLI SEL, S, TDI, TDI Premium | 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS

Volkswagen Jetta MAP Sensor

Choose OEM MAP Sensor for superior quality and long-lasting durability. They match the Volkswagen's factory specifications exactly and pass strict quality control. If you plan to replace MAP Sensor on your Jetta, put OEM at the top of your list. You'll get the right fit, reliable performance, and peace of mind. We stock an extensive inventory of genuine Volkswagen Jetta parts. It is easy to find what you need. You will love our competitive prices that help you save. No more hassle with returns or guesswork. Every part includes a warranty straight from the manufacturer. Get trusted quality, strong durability, and real value today.

Volkswagen Jetta MAP Sensor Parts and Q&A

Pressure Sensor
03L-906-051-D
Q: How to remove and install the Air Temperature Sensor and MAP Sensor on Volkswagen Jetta?
A:
The process is used on all engines other than 2.0L turbocharged CBFA and CCTA engines, the MAP sensor is positioned on the intake manifold and it is near the throttle body. The Intake Air Temperature (IAT) sensor goes hand in hand with the MAP sensor and is referred to as Intake Manifle Sensor. Start by taking away the engine cover. In the case of 1.4L engines, the air filter housing is to be taken out. The second step is to find and unconnect the electrical connector of the MAP/IAT sensor. Unclip the MAP sensor off the manifold or loosen the mounting fasteners wherever possible but take care not to lose the O-ring because there is no replacement part, a new sensor is supplied. Installation is a backward process of removal.
Map Sensor
04E-906-051
Q: How is the MAP Sensor accessed in the charge air intake duct on Volkswagen Jetta?
A:
The sensor is located in the charge air intake duct. For 1.8L and 2.0L CPLA, CPPA, CPKA, and CPRA engines, the air filter housing assembly must be removed to access the sensor. For all other 1.8L and 2.0L engines, the front of the vehicle should be raised and supported on jackstands, followed by the removal of the engine undercover. Once located, the electrical connector should be disconnected. The sensor fasteners need to be removed or the tabs released, allowing for the sensor to be taken out of the duct. The O-ring should be discarded, and a new one must be used during the installation of the same sensor, which is done in reverse order of removal.