How should the hood be removed and installed properly on Volkswagen Jetta?

Removing and installing the hood is a tedious task and thus, there are no less than two individuals who should undertake the task. Start with blankets or pads over the cowl of the body and the fenders. To remove the harness/hoses, pry out and unconnect the harness/hoses on the bottom of the hood, pry the grommet out, and then pull the harness/hoses out of the hood. Using a permanent marker, make alignment marks around the hinge plates so that the installation is the same. Get an assistant to assist in the support of the hood and then remove the upper end of hood support strut where applicable. Take off the hinge to hood nuts and the hood can be removed and it is the same to put it back on. To adjust, the fore-and-aft and the side-to-side placement is performed by sliding the hood up and down in relation to the hinge plates by means of loosening the nuts. Unscrew the nuts and just move the hood into position little by little. Screw the hinge nuts and lower the hood slowly checking the alignment. To provide a flat hood that aligns with the fenders when closed, turn the hood bumpers inwards or outwards and to raise or lower the hood height, screw the bumpers inwards or outwards. The loosening of the nuts also allows the adjustment of the hood latch assembly or the safety lever up-and-down and side-to-side.

Genuine Volkswagen Jetta Hood

Engine Hood

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Hoods found

View related parts
Volkswagen Jetta Hood Part Number: 5K0-823-031-G
$293.67 MSRP: $401.19
You Save: $107.52 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 5K0-823-031
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2010-2014 Volkswagen Jetta | S, SE, SEL, TDI | 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS, 5 Cyl 2.5 L GAS
View related parts
Volkswagen Jetta Hood Part Number: 1J5-823-031-B
$300.74 MSRP: $410.85
You Save: $110.11 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 1J5-823-031-A
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1999-2005 Volkswagen Jetta | GL, GL TDI, GLI, GLS, GLS TDI, GLX, TDI, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Jetta Hood Part Number: 1K0-823-031-J
$374.05 MSRP: $511.00
You Save: $136.95 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 1K0-823-031-E, 1K0-823-031-G
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2005-2010 Volkswagen Jetta | 2.0T, 2.5, GL, GL TDI, GLI, GLS, GLS TDI, S, SE, SEL, TDI, TDI Cup Edition, Value Edition, Wolfsburg Edition | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS, 5 Cyl 2.5 L GAS
View related parts
Volkswagen Jetta Hood Part Number: 17A-823-031
$416.31 MSRP: $568.73
You Save: $152.42 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 17A-823-031-A
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2019-2024 Volkswagen Jetta | GLI 35th Anniversary Edition, GLI Autobahn, GLI S, R-Line, S, SE, SEL, SEL Premium, Sport | 4 Cyl 1.4 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Hood Part Number: 5C6-823-031-E
$458.60 MSRP: $626.50
You Save: $167.90 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 5C6-823-031-A, 5C6-823-031-C, 5C6-823-031-D, 5C6-823-031-B
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 2011-2018 Volkswagen Jetta | Base, GLI, GLI SE, GLI SEL, Hybrid, Hybrid SE, Hybrid SEL, Hybrid SEL Premium, S, SE, SE Sport, SEL, SEL Premium, Sport, TDI, TDI Premium, TDI S, TDI SE, TDI SEL, Wolfsburg Edition | 4 Cyl 1.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS, 5 Cyl 2.5 L GAS
View related parts
Volkswagen Jetta Hood Part Number: 191-823-031-E
$36.49 MSRP: $50.68
You Save: $14.19 (28%)
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1985-1992 Volkswagen Jetta | Base, Carat, GL, GLI, GLI 16-Valve, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Jetta Hood Part Number: 1HM-823-031-F
$258.73 MSRP: $353.50
You Save: $94.77 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Volkswagen's factory warranty.
Fits the following Vehicles:
- 1993-1999 Volkswagen Jetta | Celebration Edition, City, GL, GLS, GLX, GT, Jazz, K2, Limited Edition, TDI, Trek, Wolfsburg Edition | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS

Volkswagen Jetta Hood

The Volkswagen Jetta Hood protects the engine compartment of the car against flying stones and rain, but it also provides the car with a sleek surface through which the air passes. The hinge panel is applied to access belts, fluids, and spark plugs because the panel opens either forward or upward, allowing easy access. Throughout generations, Volkswagen has provided strong, impact-resistant steel, light aluminum, and fiberglass components in gelcoat finish that are the highly weight-saving. Ready-primed panels come in; then all that is required is a custom paint, whereas gelcoat units only require a spray to conceal the natural weave. Elective scoops and vents draw cool air into the bay and provide the Jetta with a distinctive look. In any form, the built-in crumple zones collapse on a frontal impact, thus absorbing the impact before it can reach the occupants. Each Hood also contributes to the aerodynamics of the vehicle by ensuring that the wind flows over the front in a smooth manner, allowing the Volkswagen to remain stable at highway speeds. Selecting the appropriate year-specific fit is essential since the dimensions of the Volkswagen and the location of the latches change a bit with every update. When a Hood is appropriately matched, the engine is kept safe, clean air passes through the engine, and the car looks smooth.

Choose OEM Hood for superior quality and long-lasting durability. They match the Volkswagen's factory specifications exactly and pass strict quality control. If you plan to replace Hood on your Jetta, put OEM at the top of your list. You'll get the right fit, reliable performance, and peace of mind. We stock an extensive inventory of genuine Volkswagen Jetta parts. It is easy to find what you need. You will love our competitive prices that help you save. No more hassle with returns or guesswork. Every part includes a warranty straight from the manufacturer. Get trusted quality, strong durability, and real value today.

Volkswagen Jetta Hood Parts and Q&A

Hood
5C6-823-031-E
Q: How should the hood be removed and installed properly on Volkswagen Jetta?
A:
Removing and installing the hood is a tedious task and thus, there are no less than two individuals who should undertake the task. Start with blankets or pads over the cowl of the body and the Fenders. To remove the harness/hoses, pry out and unconnect the harness/hoses on the bottom of the hood, pry the grommet out, and then pull the harness/hoses out of the hood. Using a permanent marker, make alignment marks around the hinge plates so that the installation is the same. Get an assistant to assist in the support of the hood and then remove the upper end of hood support strut where applicable. Take off the hinge to hood nuts and the hood can be removed and it is the same to put it back on. To adjust, the fore-and-aft and the side-to-side placement is performed by sliding the hood up and down in relation to the hinge plates by means of loosening the nuts. Unscrew the nuts and just move the hood into position little by little. Screw the hinge nuts and lower the hood slowly checking the alignment. To provide a flat hood that aligns with the fenders when closed, turn the hood bumpers inwards or outwards and to raise or lower the hood height, screw the bumpers inwards or outwards. The loosening of the nuts also allows the adjustment of the Hood Latch assembly or the safety lever up-and-down and side-to-side.