How to remove and reinstall the rear Steering Knuckle and rear Wheel Hub in a vehicle's rear suspension components on Volkswagen Passat?

Relax the wheel bolts and rear driveaxle hub bolt and then raise the back of the vehicle and place it on jackstands to make sure it is firmly secured. The next step is to take off the rear brake caliper, mount and brake disc bearing in mind to hold the caliper with a piece of wire or a piece of string to keep the hose away. And continue with the removal of the ABS rear wheel speed sensor. Position the camber adjusting cam relative to the lower control arm to maintain the camber positioning during reassembly and unscrew the nut on the other end of the bolt, remove the eccentric washer and draw the bolt. Unscrew the nut and take off the track rod-to-rear knuckle bolt then the upper control arm-to-rear knuckle bolt and then disassemble the knuckle and hub assembly. To install, it is necessary to reverse the steps used to remove the items, but be sure to install new hardware and make the match marks on the camber adjusting cam and the lower control arm and do not tighten any suspension fastener until the rear suspension is raised to replicate normal ride height, which prevents distortion of the bushings. Lastly, fully screw all suspension fasteners to desired torques, put brake disc and mounting bracket with caliper onto the car, and screw the brake fasteners to the correct torque before installing the wheel, screwing the bolts secure, and lowering the vehicle then screwing the bolts to recommended tightness.

How to remove the hub and wheel bearing assembly when replacing the steering knuckle on Volkswagen Jetta?

Disassemble the hub and the wheel bearing when the steering knuckle is to be replaced. The first step is to remove the wheel cover and loosen the driveaxle/hub bolt when the vehicle is on wheels, and then loosen the wheel bolts. Put the rear wheels in chock, use the parking brake, lift up the front of the car and place it safely on jackstands before removal of the front wheel. Then loosen the driveaxle/hub bolt and the ABS wheel speed sensor and brake caliper without dismounting the hose, secured the caliper to the coil spring to prevent any strain on the hose. Loosen a few turns of the balljoint-to-steering knuckle nut and then remove the tie-rod end of the steering knuckle and the balljoint of the control arm and part the balljoint and knuckle. Disconnect the front level control sensor arm with the control arm, in case equipped. Take the strut-to-knuckle nut out and hammer and punch out the bolt, taking care to make the opening where the strut inserts into the knuckle open wide where this might happen. Gently remove the knuckle assembly outwards and push the driveaxle out of the hub with a soft faced hammer to tap the CV joint out or a puller to loosen it out. secured driveaxle. To install, first install the balljoint into the knuckle and tighten the new nut to the required torque. Apply multi-purpose grease to the splines of the driveaxle, and then insert the knuckle/hub assembly in place and connect it to the driveaxle stub shaft, put a new driveaxle/hub bolt in place but not tightened. Attach the strut to the knuckle, and enter it as far as possible into the bore, and apply and organize the new nut and bolt to the required torque. Install the control arm to the balljoint and install and tighten new nuts to the recommended torque. Insert the tie-rod end into the steering knuckle and attach and tighten the new retaining nut. Install the caliper disc and caliper tighten the caliper mounting bracket bolts and caliper guide pin/mounting bolts to designated torque. Essentially, last but not least, screw the driveaxle/hub bolt on safely, screw in the ABS wheel speed sensor, replace the wheel again, lower the vehicle to the ground, and screw the driveaxle/hub bolt and wheel bolts to the required torque.

Genuine Volkswagen Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

121 Steering Knuckles found

View related parts
Volkswagen Knuckle Part Number: 5QM-407-255-A
$93.83 MSRP: $131.42
You Save: $37.59 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Knuckle
- Position: Left
- Replaced by: 5QM-407-255-B
Fits the following Volkswagen Models:
- Jetta | 2019-2024 | GLI 35th Anniversary Edition, GLI Autobahn, GLI S, R-Line, S, SE, SEL, SEL Premium, Sport | 4 Cyl 1.4 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
- Taos | 2022-2024 | S, SE, SEL | 4 Cyl 1.5 L GAS
View related parts
Volkswagen Knuckle Part Number: 5QN-505-436-A
$226.67 MSRP: $317.47
You Save: $90.80 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
Fits the following Volkswagen Models:
- Tiguan | 2021-2024 | S, SE, SE R-Line Black, SEL, SEL Premium R-Line, SEL R-Line | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Knuckle Part Number: 5QN-505-435-A
$259.38 MSRP: $354.35
You Save: $94.97 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
Fits the following Volkswagen Models:
- Tiguan | 2021-2024 | S, SE, SE R-Line Black, SEL, SEL Premium R-Line, SEL R-Line | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Knuckle Part Number: 171-407-255-B
$191.35 MSRP: $268.00
You Save: $76.65 (29%)
ADD TO CART
Product Specifications
- Other Name: Housing; Knuckle
- Position: Left
Fits the following Volkswagen Models:
- Cabriolet | 1985-1993 | Base, Bestseller, Boutique, Carat, Classic, Etienne Aigner, Wolfsburg Edition | 4 Cyl 1.8 L GAS
- Scirocco | 1985-1988 | 16-Valve, Base | 4 Cyl 1.8 L GAS
View related parts
Volkswagen Knuckle Part Number: 171-407-256-A
$191.35 MSRP: $268.00
You Save: $76.65 (29%)
ADD TO CART
Product Specifications
- Other Name: Housing; Steering Knuckle
- Position: Right
Fits the following Volkswagen Models:
- Cabriolet | 1985 | Base | 4 Cyl 1.8 L GAS
- Golf | 1986 | Base, GTI | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS
- Jetta | 1984-1986 | Base, GL, GLI | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.7 L GAS, 4 Cyl 1.8 L GAS
- Rabbit | 1984 | GL, GTI, L, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.7 L GAS, 4 Cyl 1.8 L GAS
- Rabbit Convertible | 1984 | Base, Wolfsburg Edition | 4 Cyl 1.8 L GAS
- Scirocco | 1984 | Base | 4 Cyl 1.8 L GAS
View More
View related parts
Volkswagen Knuckle Part Number: 5QM-505-435-C
$376.54 MSRP: $514.40
You Save: $137.86 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
Fits the following Volkswagen Models:
- Taos | 2022-2024 | S, SE, SEL | 4 Cyl 1.5 L GAS
View related parts
Volkswagen Knuckle Part Number: 5QM-505-436-C
$376.54 MSRP: $514.40
You Save: $137.86 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
Fits the following Volkswagen Models:
- Taos | 2022-2024 | S, SE, SEL | 4 Cyl 1.5 L GAS
View related parts
Volkswagen Knuckle Part Number: 171-407-256-B
$204.68 MSRP: $286.67
You Save: $81.99 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Steering Knuckle
- Position: Right
Fits the following Volkswagen Models:
- Cabriolet | 1985-1993 | Base, Bestseller, Boutique, Carat, Classic, Etienne Aigner, Wolfsburg Edition | 4 Cyl 1.8 L GAS
- Golf | 1985 | Base, GTI | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS
- Scirocco | 1985-1988 | 16-Valve, Base | 4 Cyl 1.8 L GAS
View More
View related parts
Volkswagen Knuckle Part Number: 5QM-407-256-A
$252.72 MSRP: $345.24
You Save: $92.52 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Knuckle
- Position: Right
- Replaced by: 5QM-407-256-B
Fits the following Volkswagen Models:
- Jetta | 2019-2024 | GLI 35th Anniversary Edition, GLI Autobahn, GLI S, R-Line, S, SE, SEL, SEL Premium, Sport | 4 Cyl 1.4 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
- Taos | 2022-2024 | S, SE, SEL | 4 Cyl 1.5 L GAS
View related parts
Volkswagen Knuckle Part Number: 191-407-256-C
$214.20 MSRP: $300.00
You Save: $85.80 (29%)
ADD TO CART
Product Specifications
- Other Name: Housing; Steering Knuckle
Fits the following Volkswagen Models:
- Golf | 1987-1992 | Base, GL, GT, GTI, GTI 16-Valve, GTI 8-Valve | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Jetta | 1997-1999, 1987-1992 | Base, Carat, GL, GLI 16-Valve, TDI, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Knuckle Part Number: 1H0-407-255
$252.54 MSRP: $345.00
You Save: $92.46 (27%)
ADD TO CART
Product Specifications
- Other Name: Housing; Steering Knuckle
- Position: Left
Fits the following Volkswagen Models:
- Corrado | 1992-1994 | SLC | 6 Cyl 2.8 L GAS
- Golf | 1995-1998 | GTI VR6 | 6 Cyl 2.8 L GAS
- Jetta | 1994-1999 | GLX | 6 Cyl 2.8 L GAS
- Passat | 1995-1997 | GLX | 6 Cyl 2.8 L GAS
View More
View related parts
Volkswagen Knuckle Part Number: 1H0-407-256
$253.64 MSRP: $346.50
You Save: $92.86 (27%)
ADD TO CART
Product Specifications
- Other Name: Housing; Steering Knuckle
Fits the following Volkswagen Models:
- Corrado | 1992-1994 | SLC | 6 Cyl 2.8 L GAS
- Golf | 1995-1998 | GTI VR6 | 6 Cyl 2.8 L GAS
- Jetta | 1994-1999 | GLX | 6 Cyl 2.8 L GAS
- Passat | 1993-1997 | GLX | 6 Cyl 2.8 L GAS
View More
View related parts
Volkswagen Steering Knuckle Part Number: 191-407-255-B
$260.59 MSRP: $356.00
You Save: $95.41 (27%)
ADD TO CART
Product Specifications
- Other Name: Housing
- Position: Left
Fits the following Volkswagen Models:
- Golf | 1985-1987 | Base, GL, GT, GTI, GTI 16-Valve | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS
- Jetta | 1985-1987 | Base, GL, GLI, GLI 16-Valve, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS
View related parts
Volkswagen Steering Knuckle Part Number: 191-407-256-B
$260.59 MSRP: $356.00
You Save: $95.41 (27%)
ADD TO CART
Product Specifications
- Other Name: Housing
- Position: Right
Fits the following Volkswagen Models:
- Golf | 1985-1987 | Base, GL, GT, GTI, GTI 16-Valve | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS
- Jetta | 1985-1987 | Base, GL, GLI, GLI 16-Valve, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS
View related parts
Volkswagen Knuckle Part Number: 191-407-255-C
$261.29 MSRP: $356.95
You Save: $95.66 (27%)
ADD TO CART
Product Specifications
- Other Name: Housing; Steering Knuckle
- Position: Left
- Replaces: 191-407-255-D, 191-407-256-D
Fits the following Volkswagen Models:
- Golf | 1987-1992 | Base, GL, GT, GTI, GTI 16-Valve, GTI 8-Valve | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Jetta | 1987-1992 | Base, Carat, GL, GLI 16-Valve, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Knuckle Part Number: 701-407-312-G
$268.79 MSRP: $367.20
You Save: $98.41 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
- Position: Right
Fits the following Volkswagen Models:
- EuroVan | 1997, 1995, 1993 | Camper, CL, GL, MV | 5 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Knuckle Part Number: 701-407-311-G
$281.62 MSRP: $384.73
You Save: $103.11 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
- Position: Left
Fits the following Volkswagen Models:
- EuroVan | 1993 | CL, GL, MV | 5 Cyl 2.5 L GAS
View related parts
Volkswagen Knuckle Part Number: 1H0-407-255-B
$291.58 MSRP: $398.33
You Save: $106.75 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
- Position: Left
Fits the following Volkswagen Models:
- Golf | 1997-1999 | GL, K2, TDI | 4 Cyl 1.9 L DIESEL
- Jetta | 1998 | TDI | 4 Cyl 1.9 L DIESEL
View related parts
Volkswagen Knuckle Part Number: 1H0-407-256-B
$291.58 MSRP: $398.33
You Save: $106.75 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
- Position: Right
Fits the following Volkswagen Models:
- Golf | 1997-1999 | GL, K2, TDI | 4 Cyl 1.9 L DIESEL
- Jetta | 1998 | TDI | 4 Cyl 1.9 L DIESEL
View related parts
Volkswagen Knuckle Part Number: 3Q0-505-435-M
$348.20 MSRP: $475.68
You Save: $127.48 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Knuckle
- Position: Left
Fits the following Volkswagen Models:
- Arteon | 2019-2023 | SE, SE R-Line, SEL, SEL Premium, SEL Premium R-Line, SEL R-Line | 4 Cyl 2.0 L GAS

| Page 1 of 7 |Next >

1-20 of 121 Results

Volkswagen Steering Knuckle

The essential part of the suspension system, the Volkswagen steering knuckle, connects the suspension and wheel assembly. The steering knuckle is directly controlled by the steering wheel. The steering knuckle turns the wheels in your car with a ball joint. It can lead to inaccurate steering angles, asymmetric tire erosion, and even distorted brake pistons if you use a broken steering knuckle when driving. Therefore, car owners should regularly check, repair, or replace it as necessary for their safety while driving at ease.

OEM (Original Equipment Manufacturer) Volkswagen Steering Knuckles are perfect for motorists because they are the best quality parts produced as per the manufacturer's specifications; hence, they perform well and are reliable too, thus helping to retain the car's initial functionality as well as safety features. At VWPartsGiant.com, our genuine Volkswagen Steering Knuckle supply indicates how much we care about the health of your vehicle. Additionally, our stock is vast, so every product will be easily accessible to you for finding and swapping without fear of making mistakes. With our user-friendly online catalog, it takes no time to identify the right spare part. Therefore, convenience accompanies servicing or maintaining a motorcar. You can rely on our OEM Volkswagen Steering Knuckle to sustain the performance of your automobile.

Volkswagen Steering Knuckle Parts and Q&A

Knuckle
4B0-505-434-A
Q: How to remove and reinstall the rear Steering Knuckle and rear Wheel Hub in a vehicle's rear suspension components on Volkswagen Passat?
A:
Relax the wheel bolts and rear driveaxle hub bolt and then raise the back of the vehicle and place it on jackstands to make sure it is firmly secured. The next step is to take off the rear brake caliper, mount and brake disc bearing in mind to hold the caliper with a piece of wire or a piece of string to keep the hose away. And continue with the removal of the ABS rear wheel speed sensor. Position the camber adjusting cam relative to the lower control arm to maintain the camber positioning during reassembly and unscrew the nut on the other end of the bolt, remove the eccentric washer and draw the bolt. Unscrew the nut and take off the track rod-to-rear knuckle bolt then the upper control arm-to-rear knuckle bolt and then disassemble the knuckle and hub assembly. To install, it is necessary to reverse the steps used to remove the items, but be sure to install new hardware and make the match marks on the camber adjusting cam and the lower control arm and do not tighten any suspension fastener until the rear suspension is raised to replicate normal ride height, which prevents distortion of the bushings. Lastly, fully screw all suspension fasteners to desired torques, put brake disc and mounting bracket with caliper onto the car, and screw the brake fasteners to the correct torque before installing the wheel, screwing the bolts secure, and lowering the vehicle then screwing the bolts to recommended tightness.
Knuckle
5C0-407-255
Q: How to remove the hub and wheel bearing assembly when replacing the steering knuckle on Volkswagen Jetta?
A:
Disassemble the hub and the wheel bearing when the steering knuckle is to be replaced. The first step is to remove the wheel cover and loosen the driveaxle/hub bolt when the vehicle is on wheels, and then loosen the wheel bolts. Put the rear wheels in chock, use the parking brake, lift up the front of the car and place it safely on jackstands before removal of the front wheel. Then loosen the driveaxle/hub bolt and the ABS wheel speed sensor and brake caliper without dismounting the hose, secured the caliper to the coil spring to prevent any strain on the hose. Loosen a few turns of the balljoint-to-steering knuckle nut and then remove the tie-rod end of the steering knuckle and the balljoint of the control arm and part the balljoint and knuckle. Disconnect the front level control sensor arm with the control arm, in case equipped. Take the strut-to-knuckle nut out and hammer and punch out the bolt, taking care to make the opening where the strut inserts into the knuckle open wide where this might happen. Gently remove the knuckle assembly outwards and push the driveaxle out of the hub with a soft faced hammer to tap the CV joint out or a puller to loosen it out. secured driveaxle. To install, first install the balljoint into the knuckle and tighten the new nut to the required torque. Apply multi-purpose grease to the splines of the driveaxle, and then insert the knuckle/hub assembly in place and connect it to the driveaxle stub shaft, put a new driveaxle/hub bolt in place but not tightened. Attach the strut to the knuckle, and enter it as far as possible into the bore, and apply and organize the new nut and bolt to the required torque. Install the control arm to the balljoint and install and tighten new nuts to the recommended torque. Insert the tie-rod end into the steering knuckle and attach and tighten the new retaining nut. Install the caliper disc and caliper tighten the caliper mounting bracket bolts and caliper guide pin/mounting bolts to designated torque. Essentially, last but not least, screw the driveaxle/hub bolt on safely, screw in the ABS wheel speed sensor, replace the wheel again, lower the vehicle to the ground, and screw the driveaxle/hub bolt and wheel bolts to the required torque.