How to remove and install the driveshaft on Volkswagen Golf R?

The subsequent process is limited to Goff AWD models. The first thing to do is to lift up the front of the vehicle and place it safely on jackstands. To provide clearance in the removal of driveshafts and in case of need, remove the under body panels, and remove the muffler and exhaust pipes. Disassemble the bolts that hold the lower matching transaxle mount bracket on the transaxle, and then rotate the engine and transaxle forward, and support it in place using a block of wood. Then, take out the bolts and the driveshaft heat shield of the transfer case and the bolts and center heat shield of the body. Removed the mounting nuts and rear tunnel brace of the vehicle the driveshaft rubber discs are marked relative to the flanges on the differential and transfer case to fit during installation. When you are still holding the driveshaft intact, loosen the driveshaft flange bolts keeping the ends of the driveshaft in place so that they are not destroyed. Using the help, a center of the driveshaft with the support and take out the center support bolts, however, in some models, the supports can be two, and the removal of the fasteners is necessary. Slowly removed the driveshaft out of the car without destroying the bushing within the ends. To install it, undo the steps of removal, making sure that a second party is involved. Install the rubber discs at the identified points, and screw the bolts of the rubber discs to the flanges and loosely fit the center support nuts to hold the driveshaft. Install the bolts binding the rubber discs to the flanges to the differential and transfer case to the correct tightness, and then tighten the center support nuts with the support in a neutral position. Installing Installing the installation involves reverse removal.

What precautions should be taken when handling the driveshaft, and what steps are involved in its removal and installation on Volkswagen Passat?

It is important to remember that the driveshaft should not be bent at an angle steeper than 25 degrees and it is recommended that a holding device be used to hold both halves straight and this can be constructed of a piece of 2x4 of the correct size with wooden blocks at both ends. In case of the unavailability of a fixture, hold the driveshaft in a flat position with the help of a floor jack or otherwise. As of now, the drive shaft cannot be replacement parts so when the CV joints, U-joint, or center support bearing wear, the whole part will have to be replaced and it would be advisable to consult a professional in the field of drivelines to see what can be done to salvage the situation. The first thing to do is to elevate the vehicle and place it on jackstands and mark the position of the CV joints relative to the respective flanges. Hold up one end of the driveshaft and the other with support then loosen the bolts holding the CV joints in place. The next step is to take out the nuts connecting the center support bearing bracket to the floorpan with a note of the shim positions and remove the driveshaft carefully. To install them, follow the steps of removal in reverse though making sure that previous gasket material is removed and new gaskets are installed, new CV joint bolts are installed, heat shield must be restored to its original position, and shims should be returned to their original locations. Prior to attaching the center support bearing nuts, slide the bearing to the front and rear to indicate the position of the bracket on the floorpan then position the bracket in between the two indications and tighten all fasteners to the recommended values.

Genuine Volkswagen Driveshaft

Drive Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Driveshafts found

View related parts
Volkswagen Drive Shaft Part Number: 3QF-521-101-M
$713.08 MSRP: $899.21
You Save: $186.13 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
- Replaced by: 3QF-521-101-P
Fits the following Volkswagen Models:
- Atlas | 2018-2024 | Launch Edition, Peak Edition SE, Peak Edition SEL, S, SE, SE R-Line, SEL, SEL Premium, SEL Premium R-Line, SEL R-Line, SEL R-Line Black | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
- Atlas Cross Sport | 2020-2024 | S, SE, SE R-Line, SEL, SEL Premium, SEL Premium R-Line, SEL R-Line, SEL R-Line Black, Trendline | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 7P0-521-101-N
$850.73 MSRP: $1072.80
You Save: $222.07 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
- Replaces: 7P0-521-101-G, 7P0-521-101-F, 7P0-521-101-K
Fits the following Volkswagen Models:
- Touareg | 2011-2016 | TDI, TDI Executive, TDI Lux, TDI R-Line, TDI Sport, X | 6 Cyl 3.0 L DIESEL
View related parts
Volkswagen Drive Shaft Part Number: 7P0-521-101-Q
$887.72 MSRP: $1119.45
You Save: $231.73 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft; Drive Shaft
- Replaced by: 7P0-521-101-R
- Replaces: 7P0-521-101-E, 7P0-521-101-H, 7P0-521-101-M, 7P0-521-101-J
Fits the following Volkswagen Models:
- Touareg | 2011-2017 | Hybrid, V6 Executive, V6 Lux, V6 R-Line, V6 Sport, V6 Wolfsburg, VR6 | 6 Cyl 3.0 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.6 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 5WA-521-101-K
$933.82 MSRP: $1177.59
You Save: $243.77 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
Fits the following Volkswagen Models:
- Golf R | 2022-2023 | 20th Anniversary Edition, Base | 4 Cyl 2.0 L GAS
- Taos | 2022-2024 | S, SE, SEL | 4 Cyl 1.5 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 7P0-521-102-T
$1129.83 MSRP: $1424.76
You Save: $294.93 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
Fits the following Volkswagen Models:
- Touareg | 2011-2017 | TDI, TDI Executive, TDI Lux, TDI R-Line, TDI Sport, V6 Executive, V6 Lux, V6 R-Line, V6 Sport, V6 Wolfsburg, VR6, X | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 5WA-521-101-T
$1331.59 MSRP: $1559.24
You Save: $227.65 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
Fits the following Volkswagen Models:
- Golf R | 2023 | 20th Anniversary Edition, Base | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 5QF-521-101-S
$1380.87 MSRP: $1616.94
You Save: $236.07 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft; Drive Shaft
Fits the following Volkswagen Models:
- Tiguan | 2018-2024 | S, SE, SE R-Line Black, SEL, SEL Premium, SEL Premium R-Line, SEL R-Line, SEL R-Line Jet Black | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 3C0-521-101-AJ
$1382.03 MSRP: $1618.29
You Save: $236.26 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft; Drive Shaft
- Replaces: 3C0-521-101-AF, 3C0-521-101-L, 3C0-521-101-AD
Fits the following Volkswagen Models:
- CC | 2009-2016 | 4 Motion, Executive, Executive 4 Motion, Lux, Lux Limited, Lux Plus, Luxury, R-Line, R-Line Executive, Sport, Sport Plus, Trend, V6 Executive 4Motion, VR6, VR6 4Motion, VR6 4Motion Executive, VR6 Sport | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
- Passat | 2006-2008 | 2.0T, 3.6, Komfort, Lux, Turbo, Value Edition, VR6, Wolfsburg Edition | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 3B0-521-101-R
$1268.80 MSRP: $1485.71
You Save: $216.91 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
- Replaces: 3B0-521-101-D
Fits the following Volkswagen Models:
- Passat | 1999-2005 | 4 Motion, GL, GLS, GLS 4 Motion, GLX, GLX 4 Motion, W8 | 4 Cyl 1.8 L GAS, 6 Cyl 2.8 L GAS, 8 Cyl 4.0 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 3Q0-521-101-AR
$1104.09 MSRP: $1392.30
You Save: $288.21 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft; Drive Shaft, Drive Shaft Assembly
Fits the following Volkswagen Models:
- Arteon | 2019-2023 | SE, SE R-Line, SEL, SEL Premium, SEL Premium R-Line, SEL R-Line | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 5N0-521-101-N
$1466.10 MSRP: $1716.74
You Save: $250.64 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
- Replaces: 5N0-521-101-H
Fits the following Volkswagen Models:
- Tiguan | 2009-2017 | R-Line, S, SE, SEL, Sport, Wolfsburg Edition | 4 Cyl 2.0 L GAS
- Tiguan Limited | 2017-2018 | Base | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 5Q0-521-101-BJ
$1466.10 MSRP: $1716.74
You Save: $250.64 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft; Drive Shaft, Propeller Shaft
- Replaces: 5Q0-521-101-AT, 5Q0-521-101-AJ, 5Q0-521-101-BA
Fits the following Volkswagen Models:
- Golf Alltrack | 2017-2019 | S, SE, SEL | 4 Cyl 1.8 L GAS
- Golf R | 2015-2019 | Base | 4 Cyl 2.0 L GAS
- Golf SportWagen | 2017-2019 | S, SE, SEL | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L GAS
View More
View related parts
Volkswagen Propeller Shaft Part Number: 7L6-521-101-N
$864.66 MSRP: $1090.37
You Save: $225.71 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 7L6-521-101-E, 7L6-521-101-G, 7L6-521-101-C, 7L6-521-101-A
Fits the following Volkswagen Models:
- Touareg | 2005-2008 | TDI | 10 Cyl 5.0 L DIESEL
View related parts
Volkswagen Drive Shaft Part Number: 7L6-521-102-Q
$1126.46 MSRP: $1420.51
You Save: $294.05 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft; Drive Shaft
- Replaces: 7L6-521-102-D, 7L6-521-102-N, 7L6-521-102-F, 7L6-521-102-H, 7L6-521-102-E
Fits the following Volkswagen Models:
- Touareg | 2005-2008 | TDI | 10 Cyl 5.0 L DIESEL
View related parts
Volkswagen Drive Shaft Part Number: 7P0-521-102-Q
$1129.83 MSRP: $1424.76
You Save: $294.93 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
- Replaced by: 7P0-521-102-S
- Replaces: 7P0-521-102-N, 7P0-521-102-J, 7P0-521-102-L
Fits the following Volkswagen Models:
- Touareg | 2011-2015 | Hybrid | 6 Cyl 3.0 L FULL HYBRID EV-GAS (FHEV)
View related parts
Volkswagen Drive Shaft Part Number: 7L0-521-102-N
$1143.29 MSRP: $1441.72
You Save: $298.43 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft; Drive Shaft
- Replaces: 7L0-521-102-M, 7L0-521-102-D, 7L0-521-102-H, 7L0-521-102-B, 7L0-521-102-G
Fits the following Volkswagen Models:
- Touareg | 2004-2010 | Base, TDI, V6, VR6 | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.2 L GAS, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 7L6-521-102-P
$1143.29 MSRP: $1441.72
You Save: $298.43 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft; Drive Shaft
- Replaces: 7L6-521-102-J, 7L6-521-102-G, 7L0-521-102-F, 7L6-521-102-M
Fits the following Volkswagen Models:
- Touareg | 2004-2009 | Base, V8 | 8 Cyl 4.2 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 3D7-521-101-K
$1277.79 MSRP: $1496.24
You Save: $218.45 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
- Replaces: 3D7-521-101-C
Fits the following Volkswagen Models:
- Phaeton | 2004-2006 | W12 | 12 Cyl 6.0 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 3D7-521-101-L
$1316.22 MSRP: $1541.24
You Save: $225.02 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
- Replaces: 3D7-521-101-E
Fits the following Volkswagen Models:
- Phaeton | 2004-2006 | V8 | 8 Cyl 4.2 L GAS
View related parts
Volkswagen Drive Shaft Part Number: 1J0-521-101-AL
$1345.66 MSRP: $1575.71
You Save: $230.05 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Propeller Shaft
Fits the following Volkswagen Models:
- R32 | 2004 | Base | 6 Cyl 3.2 L GAS

| Page 1 of 2 |Next >

1-20 of 22 Results

Volkswagen Driveshaft

Volkswagen Driveshaft transmits engine power to the wheels with balanced rotation that provides every VW vehicle with smooth acceleration and steady handling even when suspension angles change on rough roads. The component is based on a strong hollow tube that can resist the twisting force, and the universal joints are pivotally free, allowing torque to flow smoothly without shuddering, so in this way, the cabin is quiet and the steering is also free from vibration. Because each Driveshaft is carefully balanced, it helps support spirited launches while avoiding excess weight, helping the whole lineup maintain quick response and good fuel economy. Protective seals trap grease within the joints to reduce friction and prolong service life so owners can enjoy dependable motion mile after mile. Founded in 1937 with the dream to create a reliable people's car, the brand has since evolved into a global icon known for clever engineering and timeless design. The classic Beetle and the adaptable Type 2 van demonstrated early the ways a VW could combine charm and utility, and today the brand brings that spirit into vehicles that offer TSI turbo engines, direct injection, digital cockpits, park assist systems, and the modular MQB platform that reduces production costs while enhancing strength. Exploration of electric mobility through the ID.3 and ID.4 proves VW is still pushing innovation, combining clean styling with advanced infotainment and head-up displays to provide drivers with technology that is intuitive and fun.

Buying OEM parts is a smart move to keep your long-term repair costs low. These components are built to last because VW uses such strict factory standards. At VWPartsGiant.com, it is easy to find genuine Volkswagen Driveshaft at prices that actually beat the competition. You get a real manufacturer's warranty with every single part, so you know your purchase is safe. Plus, forget about return headaches since our policy is easy and worry-free. We ship your order fast, too. If you have questions, our team of parts experts is ready to help. Why wait? Start shopping now!

Volkswagen Driveshaft Parts and Q&A

Drive Shaft
5Q0-521-101-BJ
Q: How to remove and install the driveshaft on Volkswagen Golf R?
A:
The subsequent process is limited to Goff AWD models. The first thing to do is to lift up the front of the vehicle and place it safely on jackstands. To provide clearance in the removal of driveshafts and in case of need, remove the under body panels, and remove the muffler and exhaust pipes. Disassemble the bolts that hold the lower matching transaxle mount bracket on the transaxle, and then rotate the engine and transaxle forward, and support it in place using a block of wood. Then, take out the bolts and the driveshaft heat shield of the transfer case and the bolts and center heat shield of the body. Removed the mounting nuts and rear tunnel brace of the vehicle the driveshaft rubber discs are marked relative to the flanges on the differential and transfer case to fit during installation. When you are still holding the driveshaft intact, loosen the driveshaft flange bolts keeping the ends of the driveshaft in place so that they are not destroyed. Using the help, a center of the driveshaft with the support and take out the center support bolts, however, in some models, the supports can be two, and the removal of the fasteners is necessary. Slowly removed the driveshaft out of the car without destroying the bushing within the ends. To install it, undo the steps of removal, making sure that a second party is involved. Install the rubber discs at the identified points, and screw the bolts of the rubber discs to the flanges and loosely fit the center support nuts to hold the driveshaft. Install the bolts binding the rubber discs to the flanges to the differential and transfer case to the correct tightness, and then tighten the center support nuts with the support in a neutral position. Installing Installing the installation involves reverse removal.
Drive Shaft
3B0-521-101-R
Q: What precautions should be taken when handling the driveshaft, and what steps are involved in its removal and installation on Volkswagen Passat?
A:
It is important to remember that the driveshaft should not be bent at an angle steeper than 25 degrees and it is recommended that a holding device be used to hold both halves straight and this can be constructed of a piece of 2x4 of the correct size with wooden blocks at both ends. In case of the unavailability of a fixture, hold the driveshaft in a flat position with the help of a floor jack or otherwise. As of now, the drive shaft cannot be replacement parts so when the CV joints, U-joint, or center support bearing wear, the whole part will have to be replaced and it would be advisable to consult a professional in the field of drivelines to see what can be done to salvage the situation. The first thing to do is to elevate the vehicle and place it on jackstands and mark the position of the CV joints relative to the respective flanges. Hold up one end of the driveshaft and the other with support then loosen the bolts holding the CV joints in place. The next step is to take out the nuts connecting the center support bearing bracket to the floorpan with a note of the shim positions and remove the driveshaft carefully. To install them, follow the steps of removal in reverse though making sure that previous gasket material is removed and new gaskets are installed, new CV joint bolts are installed, heat shield must be restored to its original position, and shims should be returned to their original locations. Prior to attaching the center support bearing nuts, slide the bearing to the front and rear to indicate the position of the bracket on the floorpan then position the bracket in between the two indications and tighten all fasteners to the recommended values.