Question 1

What precautions should be taken when disconnecting the battery and performing camshaft and rocker arm repairs for 5-cylinder engines on Volkswagen Golf?

Accepted Answer

When the battery is disconnected, a number of systems will not work up until they are re-learned again. Otherwise, severe engine damage will be experienced in case of errors and therefore cannot be carried out by just anybody unless extremely experienced in such kind of work. In case of doubts about skills, refer to a professional. Check everything and verify that everything is in order before trying to start the engine. It is important to ensure that the camshafts and lifters are fully checked before the installation, and the check of camshaft endplay also before removal. Install the camshafts in timing adjust position, and then remove the camshaft sprocket and timing chain keeping the lobes and slots aligned with the camshafts as they were before removal. There are no individual camshaft bearing caps on this engine, as all the caps are assembled into a camshaft guide frame system. Relaxation of the camshaft guide frame bolts should be done half turn at a time until the pressure in the valve springs is relieved. New guide frame bolts are necessary, since old bolts are stretch-type fasteners that cannot give the correct readings of torque once they were used. Take out the guide frame, the camshafts and any remaining remnants of gasket material that is applied on matching surfaces and never reassemble them without conducting a careful inspection to ensure that they are in perfect condition. Inspect the camshaft bearing surfaces visually and in case damaged, the guide frame and cylinder head have to be changed. Take the measurement, both in terms of width, of the outside diameter of each camshaft bearing journal and also the inside diameter of each of the respective camshaft bearings. New camshafts, lifters, or/and guide frame and cylinder head could be needed in case overly worn. In order to measure the runout of the camshaft, the camshaft should be reinserted into the cylinder head and a dial indicator placed on the center journal that measures the readings and compares them with the recommended runout. In case the runout measured is beyond the specification, then change the camshaft. Install the cylinder head cover/guide frame temporarily and measure the endplay of the camshaft with a dial indicator; in case exceeds recommended values, inspect the guide frame under investigation. Determine lobe height of camshafts by means of a micrometer, comparing intake lobes to each other and exhaust lobes to each other; within a tolerance of more than 0.005 inch, change the camshaft. Check wear and scratches on contact and sliding surfaces of every lash adjuster and roller roller of every rocker arm, and make sure lash adjusters move freely in their bores. Apply oil on the lash adjusters and roller rocker arms and then fit them in the actual places. Clean and lubricate guide frame bearing surfaces and camshafts, you have to insert the camshafts in the guide frame with the recesses facing each other. Make sure that the sealing rings of the intake camshaft are uphill or downhill to avoid leakage of oil. Then with the help, carefully roll the guide frame and ensure that the camshafts do not drop out, making sure that the thread holes are aligned and the camshaft holding tool is installed and tightened to 15 ft-lbs (20 Nm). Using 1/8 inch of RTV sealant, apply the sealant around the edges of the guide frame and the spark plug holes, and then fit the guide frame assembly to the cylinder head. Install new bolts to the guide frames and tighten them in the correct order wiping off any surplus sealant. Cure sealant according to the recommendations by the sealant manufacturer and then add oil. Insert the sealing plugs at the end of the cylinder head and the guide frame of the camshaft until they are flush. It should be left to rest with the engine not rotated at all within 30 minutes. Turn the valve timing, and take out the camshaft holding tool and crankshaft locking pin. Before turning the starter switch on, turn the crankshaft by hand at least two full revolutions; any resistance met with should cause one to halt and investigate the situation. Refill the cooling system, and the rest of the installation is the reverse of the first one, being to see that the TDC marks again coincide when the engine has been rotated 2 full revolutions.

Question 2

What precautions should be taken when disconnecting the battery and Cam Gear, Camshaft and Rocker Arm for 4-cylinder engines on Volkswagen Jetta?

Accepted Answer

When the battery has been disconnected, a number of systems will need to be re-learned until they start operating correctly. In case of mistakes, the engine will suffer serious damages; the process should not be performed by an untrained person in this kind of repair. In case uncertain of capabilities, seek advice of someone with knowledge and ensure that all work is completed before one tries to start the engine. Interim inspection of camshafts and lifters must be done before fitting, and prior to withdrawal of camshafts, endplay inspection must be done. The camshafts may not be pulled out of the camshaft housing on 1.4L (CZTA, DGXA) models, and in the situation of an issue, the camshafts and housing have to be replaced together. Untether the cable on the negative terminal of the battery, empty the cooling system, pull out air filter housing, resonator, take out the water pump, ignition coils, high-pressure fuel pump, and disconnect the electrical connector on different sensors. Disassemble the turbocharger coolant pipes, fasteners of the heat shield, upper cover of the timing belt, and position the engine at TDC. The camshaft housing bolts should be loosened in the reversal order in which they were tightened, and the camshaft housing should then be carefully removed in relation to the cylinder head, and all remnants of the gasket sealing compound removed. Cylinder head Mark and remove the roller rocker and lifters as they occur in the cylinder head, making sure that they are re-inserted in their respective positions. In the case of camshaft sprockets, special tools should be used so as not to turn when loosening bolts and installation of new seals should also be done so as to maintain cleanliness. Installation On 2.0L (CBPA) models, proceed the same way, but make sure to align and fit correctly and to use the appropriate torque specification. In 1.8L and 2.0L timing chain models, the camshaft bearings should not be machined, but should be incorporated and have to be followed through the removal and installation steps with care, checking all the marks and alignments. Refilling the cooling system, clean and lubricate all parts, and install in the right sequence and leakage.

Genuine Volkswagen Rocker Arm

18 Rocker Arms found

Volkswagen Rocker Arms Part Number: 07P-109-417-A

Volkswagen Rocker Arms Part Number: 04E-109-411-T

Volkswagen Rocker Arms Part Number: 04E-109-411-AG

Volkswagen Rocker Arms Part Number: 06E-109-417-P

Volkswagen Rocker Arms Part Number: 06N-109-417-A

Volkswagen Rocker Arms Part Number: 025-109-405-A

Volkswagen Intake Rocker Arm Part Number: 7B0-109-443

Volkswagen Intake Rocker Arm Part Number: 7B0-109-444

Volkswagen Exhaust Rocker Arms Part Number: 7B0-109-445

Volkswagen Rocker Arms Part Number: 022-109-417-E

Volkswagen Rocker Arms Part Number: 025-109-405-C

Volkswagen Rocker Arms Part Number: 7B0-109-441

Volkswagen Rocker Arms Part Number: 7B0-109-442

Volkswagen Rocker Arms Part Number: 059-109-417-J

Volkswagen Rocker Arms Part Number: 06E-109-417-S

Volkswagen Rocker Arms Part Number: 7B0-109-441-D

Volkswagen Rocker Arms Part Number: 038-109-527-AF

Volkswagen Rocker Arms Part Number: 070-109-527-B

Volkswagen Rocker Arm

Volkswagen Rocker Arm Parts and Q&A

Related Volkswagen Parts

Browse by Model