How to replace the Engine Oil Cooler on Volkswagen Jetta?

Lift the front part of the car and place it on jackstands. Working below the vehicle drain the engine coolant and remove the lower splash shield that is beneath the engine. In the case of 1.4L engines, the intake manifold must be removed and the mounting bolts of the oil cooler must be removed followed by the removal of the cooler on the side of the engine. De-assemble the four O-rings of the engine block and fit new ones. Install new O-rings to the engine block, and then fix the oil cooler and tighten the mounting bolts to the required torque. The other steps are the opposite of the removal. Recharge engine oil, coolant, and start the engine and look at leaks. With 1.8L and 2.0L engines, take out the oil filter and unscrew the electrical connectors immediately below the filter. Unscrew the mounting bolt of the oil dipstick tube, disconnect the tube on the timing chain cover and push it forward. Eliminate the fan shroud, air inlet duct and charge air cooler inlet pipe. Unconnect the electrical connector to the air conditioning compressor, and take out the compressor mounting bolts, and fix the compressor out of the mounting bracket of the sub-assembly. Take out the intake manifold support and the alternator of the sub-assembly mounting bracket. Unclip the harness of the sub-assembly bracket, disconnect the electrical connectors of the oil pressure regulator valve and the electrical connectors to the oil pressure switch and take the harness out of the way. Insert the sub-assembly mounting bracket bolts in reverse sequence of installation and slide the sub-assembly forward until the oil cooler-to-coolant pump housing connector is loosened, and then remove the sub-assembly bracket. Take out the oil cooler mounting bolts and remove the cooler out of the sub-assembly bracket. When very much of metal shavings or other debris is detected in the engine oil, wipe the areas of oil channels clean and change the engine oil cooler to avoid further damage. Disassemble and install a new seal to the oil cooler and install the new seal in the grooves of the sub-assembly bracket making sure that it is correctly positioned in the mounting bracket and the mounting bolts are properly installed to the required torque. Mount the sub-assembly bracket to the engine and screw the mounting bolts in turn to the recommended torque. The other steps are the opposite of the removal. Recharge engine oil, coolant, and start the engine and look at leaks.

Genuine Volkswagen Engine Oil Cooler

Oil Cooler

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

30 Engine Oil Coolers found

View related parts
Volkswagen Oil Cooler Part Number: 05E-117-021
$20.09 MSRP: $32.94
You Save: $12.85 (40%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Jetta | 2022-2023 | S, SE, SEL, Sport | 4 Cyl 1.5 L GAS
- Taos | 2022 | S, SE, SEL | 4 Cyl 1.5 L GAS
View related parts
Volkswagen Oil Cooler Part Number: 06Q-117-021-E
$154.69 MSRP: $216.65
You Save: $61.96 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 06Q-117-021-H
Fits the following Volkswagen Models:
- Arteon | 2022-2023 | SE R-Line, SEL Premium R-Line, SEL R-Line | 4 Cyl 2.0 L GAS
- GTI | 2022-2024 | 40th Anniversary Edition, Autobahn, S, SE | 4 Cyl 2.0 L GAS
- Golf R | 2022-2023 | 20th Anniversary Edition, Base | 4 Cyl 2.0 L GAS
View More
View related parts
Volkswagen Oil Cooler Part Number: 7B0-117-021-A
$112.59 MSRP: $158.21
You Save: $45.62 (29%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Routan | 2009-2010 | SEL, SEL Premium | 6 Cyl 4.0 L GAS
View related parts
Volkswagen Oil Cooler Part Number: 7B0-117-021-B
$203.79 MSRP: $285.42
You Save: $81.63 (29%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Routan | 2009-2010 | S, SE | 6 Cyl 3.8 L GAS
View related parts
Volkswagen Oil Cooler Part Number: 04E-117-021-K
$232.04 MSRP: $324.98
You Save: $92.94 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 04E-117-021-L
- Replaces: 04E-117-021-C
Fits the following Volkswagen Models:
- Golf | 2019-2021 | S, SE, TSi | 4 Cyl 1.4 L GAS
- Golf SportWagen | 2019 | S, SE | 4 Cyl 1.4 L GAS
- Jetta | 2013-2021 | Hybrid, Hybrid SE, Hybrid SEL, Hybrid SEL Premium, R-Line, S, SE, SEL, SEL Premium, Wolfsburg Edition | 4 Cyl 1.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.4 L GAS
View More
View related parts
Volkswagen Oil Cooler Part Number: 7B0-115-401
$418.90 MSRP: $574.20
You Save: $155.30 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter; Oil Cooler
Fits the following Volkswagen Models:
- Routan | 2011-2014 | S, SE, SEL, SEL Premium | 6 Cyl 3.6 L FLEX
View related parts
Volkswagen Oil Cooler Assembly Part Number: 07D-117-015-G
$266.12 MSRP: $363.55
You Save: $97.43 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Cooler
- Replaces: 07D-117-015-E
Fits the following Volkswagen Models:
- Passat | 2002-2004 | W8 | 8 Cyl 4.0 L GAS
View related parts
Volkswagen Oil Cooler Part Number: 06L-117-021-G
$274.49 MSRP: $374.98
You Save: $100.49 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 06L-117-021-E
Fits the following Volkswagen Models:
- Arteon | 2019-2021 | SE, SE R-Line, SEL, SEL Premium, SEL Premium R-Line, SEL R-Line | 4 Cyl 2.0 L GAS
- GTI | 2022-2023, 2015-2018 | 40th Anniversary Edition, Autobahn, S, SE, Sport | 4 Cyl 2.0 L GAS
- Golf | 2015-2017 | Base, Launch Edition, S, SE, SEL, Wolfsburg Edition | 4 Cyl 1.8 L GAS
- Golf Alltrack | 2017 | S, SE, SEL | 4 Cyl 1.8 L GAS
- Golf R | 2015-2019 | Base | 4 Cyl 2.0 L GAS
- Golf SportWagen | 2015-2017 | Limited Edition, S, SE, SEL | 4 Cyl 1.8 L GAS
View More
View related parts
Volkswagen Oil Cooler Part Number: 028-117-021-E
$298.89 MSRP: $408.32
You Save: $109.43 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 028-117-021-C
Fits the following Volkswagen Models:
- CC | 2009-2012 | Executive, VR6, VR6 4Motion, VR6 Sport | 6 Cyl 3.6 L GAS
- Passat | 2001-2005 | GL, GLS, GLS 4 Motion, GLX, GLX 4 Motion | 6 Cyl 2.8 L GAS
- R32 | 2004 | Base | 6 Cyl 3.2 L GAS
View More
View related parts
Volkswagen Oil Cooler Part Number: 077-117-021-P
$303.78 MSRP: $415.00
You Save: $111.22 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Touareg | 2004-2007 | Base, V8 | 8 Cyl 4.2 L GAS
View related parts
Volkswagen Oil Cooler Part Number: 06K-117-021-K
$308.04 MSRP: $420.82
You Save: $112.78 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 06K-117-021-G, 06K-117-021-B
Fits the following Volkswagen Models:
- Atlas | 2018-2024 | Peak Edition SE, Peak Edition SEL, S, SE, SEL, SEL Premium, SEL Premium R-Line | 4 Cyl 2.0 L GAS
- Atlas Cross Sport | 2020-2024 | S, SE, SEL, SEL Premium R-Line, SEL R-Line, SEL R-Line Black | 4 Cyl 2.0 L GAS
- Beetle | 2013-2019 | #PinkBeetle, Base, Classic, Coast, Denim, Dune, Final Edition SE, Final Edition SEL, Fleet Edition, GSR, R-Line, R-Line S, R-Line SE, R-Line SEL, S, SE, SEL, Turbo, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- GTI | 2015-2021 | Autobahn, Rabbit Edition, S, SE, Sport | 4 Cyl 2.0 L GAS
- Golf | 2017-2018 | S, SE, Wolfsburg Edition | 4 Cyl 1.8 L GAS
- Golf Alltrack | 2017-2019 | S, SE, SEL | 4 Cyl 1.8 L GAS
- Golf SportWagen | 2015-2019 | Limited Edition, S, SE, SEL | 4 Cyl 1.8 L GAS
- Jetta | 2014-2024 | Base, GLI, GLI 35th Anniversary Edition, GLI Autobahn, GLI S, GLI SE, GLI SEL, S, SE, SE Sport, SEL, SEL Premium, Sport | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Passat | 2014-2022 | Limited Edition, R-Line, S, SE, SE R-Line, SEL, SEL Premium, Sport, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Tiguan | 2018-2024 | S, SE, SE R-Line Black, SEL, SEL Premium, SEL Premium R-Line, SEL R-Line, SEL R-Line Jet Black | 4 Cyl 2.0 L GAS
View More
View related parts
Volkswagen Oil Cooler Part Number: 078-117-021-A
$308.04 MSRP: $420.82
You Save: $112.78 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Beetle | 1998-2001 | Base, GL, GLS, Sport | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Oil Cooler Part Number: 03N-117-021
$317.19 MSRP: $433.32
You Save: $116.13 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Beetle | 2015 | TDI | 4 Cyl 2.0 L DIESEL
- Jetta | 2015 | TDI S, TDI SE, TDI SEL | 4 Cyl 2.0 L DIESEL
View related parts
Volkswagen Oil Cooler Part Number: 059-117-021-K
$317.19 MSRP: $433.32
You Save: $116.13 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Touareg | 2009-2012 | TDI, TDI Executive, TDI Lux, TDI Sport | 6 Cyl 3.0 L DIESEL
View related parts
Volkswagen Cooler Part Number: 068-117-021-B
$317.19 MSRP: $433.32
You Save: $116.13 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Cooler; Cooler
- Replaces: 027-117-021-1
Fits the following Volkswagen Models:
- Beetle | 1998-2006 | GL, GLS, GLS TDI, Sport, TDI | 4 Cyl 1.9 L DIESEL
- Cabrio | 1995-2002 | Base, GL, GLS, GLX, High Line | 4 Cyl 2.0 L GAS
- EuroVan | 1999-2003, 1995, 1993 | Camper, CL, GL, GLS, MV | 5 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS
- Golf | 1993-2005 | Celebration Edition, City, GL, GLS, GTI, GTI GLX, GTI VR6, Jazz, K2, Limited Edition, Sport, TDI, Trek, Wolfsburg Edition | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
- Jetta | 1999-2004 | GLI, GLS, GLX, TDI | 4 Cyl 1.9 L DIESEL, 6 Cyl 2.8 L GAS
- Passat | 1995-1999, 1990-1993 | CL, GL, GLS, GLX, TDI | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
- Scirocco | 1984-1988 | 16-Valve, Base | 4 Cyl 1.8 L GAS
View More
View related parts
Volkswagen Oil Cooler Part Number: 068-117-021-BX
$317.19 MSRP: $433.32
You Save: $116.13 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 068-117-021-B
Fits the following Volkswagen Models:
- Cabrio | 1995-2002 | Base, GL, GLS, GLX, High Line | 4 Cyl 2.0 L GAS
- EuroVan | 1999-2003, 1995, 1993 | Camper, CL, GL, GLS, MV | 5 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS
- Golf | 1999-2002 | GL, GLS, GTI, GTI GLX, GTI VR6, TDI | 4 Cyl 1.9 L DIESEL, 6 Cyl 2.8 L GAS
- Jetta | 1999-2004 | TDI | 4 Cyl 1.9 L DIESEL
- Passat | 1998-1999 | GLS | 4 Cyl 1.8 L GAS
View More
View related parts
Volkswagen Oil Cooler Part Number: 06D-117-021-C
$317.19 MSRP: $433.32
You Save: $116.13 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Eos | 2007-2008 | 2.0T, Base, Komfort, Lux, Turbo | 4 Cyl 2.0 L GAS
- GTI | 2006-2008 | Base, Fahrenheit | 4 Cyl 2.0 L GAS
- Golf R | 2012-2013 | Base | 4 Cyl 2.0 L GAS
- Jetta | 2006-2008 | 2.0T, GLI, Wolfsburg Edition | 4 Cyl 2.0 L GAS
- Passat | 2006-2008 | 2.0T, Komfort, Lux, Turbo, Value Edition, Wolfsburg Edition | 4 Cyl 2.0 L GAS
View More
View related parts
Volkswagen Oil Cooler Part Number: 077-117-021-Q
$317.19 MSRP: $433.32
You Save: $116.13 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 077-117-021-N
Fits the following Volkswagen Models:
- Phaeton | 2004-2006 | V8 | 8 Cyl 4.2 L GAS
View related parts
Volkswagen Oil Cooler Part Number: 079-117-015-P
$362.34 MSRP: $495.01
You Save: $132.67 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 079-117-015-A
Fits the following Volkswagen Models:
- Touareg | 2007-2009 | Base | 8 Cyl 4.2 L GAS
View related parts
Volkswagen Oil Cooler Part Number: 03L-117-021-C
$287.32 MSRP: $392.52
You Save: $105.20 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Passat | 2012-2014 | TDI SE, TDI SEL, TDI SEL Premium | 4 Cyl 2.0 L DIESEL

| Page 1 of 2 |Next >

1-20 of 30 Results

Volkswagen Engine Oil Cooler

The Volkswagen Engine Oil Cooler maintains an optimal temperature of engine oil to prolong the life of the lubricant as well as protect the performance of the brand's diverse range of products. VW made its name by offering practical Beetles to everyday people, intrepid Type 2 vans, and today's sleek TSI-powered cars that ride on the cost-saving MQB platform, all in clean design that is familiar yet new. From the iconic Wolfsburg roots to the modern ID electric family, the brand strives to develop technology that is friendly and approachable, including digital cockpits, touchscreen MIB infotainment, park assist, and head-up displays, all developed to make every trip simpler and fun. VW is also focused on strong but efficient turbo engines, and that commitment to balanced engineering sets the stage for cooling solutions that protect hard-working parts. An oil cooler unit creates an essential link in this approach by circulating hot lubricant through a compact oil-to-water exchanger in which coolant draws away excess heat and allows oil to quickly warm up after startup yet not get too thin during high-rev driving or during summer traffic jams, where it could thin dangerously. The device works in harmony with the factory cooling circuit, so it fits neatly on hatchbacks, sedans, SUVs, and even future electric range extenders without special adaptations. Due to its role in stabilizing viscosity and pressure, the Engine Oil Cooler helps every VW maintain smooth acceleration, reliable towing capability, and long-term engine health that drivers can trust.

Buying OEM parts is a smart move to keep your long-term repair costs low. These components are built to last because VW uses such strict factory standards. At VWPartsGiant.com, it is easy to find genuine Volkswagen Engine Oil Cooler at prices that actually beat the competition. You get a real manufacturer's warranty with every single part, so you know your purchase is safe. Plus, forget about return headaches since our policy is easy and worry-free. We ship your order fast, too. If you have questions, our team of parts experts is ready to help. Why wait? Start shopping now!

Volkswagen Engine Oil Cooler Parts and Q&A

Oil Cooler
028-117-021-L
Q: How to replace the Engine Oil Cooler on Volkswagen Jetta?
A:
Lift the front part of the car and place it on jackstands. Working below the vehicle drain the engine coolant and remove the lower splash shield that is beneath the engine. In the case of 1.4L engines, the intake manifold must be removed and the mounting bolts of the oil cooler must be removed followed by the removal of the cooler on the side of the engine. De-assemble the four O-rings of the engine block and fit new ones. Install new O-rings to the engine block, and then fix the oil cooler and tighten the mounting bolts to the required torque. The other steps are the opposite of the removal. Recharge engine oil, coolant, and start the engine and look at leaks. With 1.8L and 2.0L engines, take out the oil filter and unscrew the electrical connectors immediately below the filter. Unscrew the mounting bolt of the oil dipstick tube, disconnect the tube on the timing chain cover and push it forward. Eliminate the fan shroud, air inlet duct and charge air cooler inlet pipe. Unconnect the electrical connector to the air conditioning compressor, and take out the compressor mounting bolts, and fix the compressor out of the mounting bracket of the sub-assembly. Take out the intake manifold support and the alternator of the sub-assembly mounting bracket. Unclip the harness of the sub-assembly bracket, disconnect the electrical connectors of the oil pressure regulator valve and the electrical connectors to the oil pressure switch and take the harness out of the way. Insert the sub-assembly mounting bracket bolts in reverse sequence of installation and slide the sub-assembly forward until the oil cooler-to-coolant pump housing connector is loosened, and then remove the sub-assembly bracket. Take out the oil cooler mounting bolts and remove the cooler out of the sub-assembly bracket. When very much of metal shavings or other debris is detected in the engine oil, wipe the areas of oil channels clean and change the engine oil cooler to avoid further damage. Disassemble and install a new seal to the oil cooler and install the new seal in the grooves of the sub-assembly bracket making sure that it is correctly positioned in the mounting bracket and the mounting bolts are properly installed to the required torque. Mount the sub-assembly bracket to the engine and screw the mounting bolts in turn to the recommended torque. The other steps are the opposite of the removal. Recharge engine oil, coolant, and start the engine and look at leaks.