What steps are needed for installing new nuts on the steering shaft connecting piece retaining plate and clamp bolt nut on Volkswagen Cabrio?

The installation will require new nuts on the intermediate shaft connecting piece that will retain the plate and a new clamp bolt nut. Start by chocking the back wheels, switching on the parking brake and lifting the front part of the car in the air using jack and supporting the vehicle on axle stands making the front wheels point in a straight direction. Disassemble the rubber boot of the firewall, the cable tie and the boot of the steering gear, sliding the boot downwards to get to the intermediate shaft. In the event of necessity, it is also possible to access it internally, prying out the retaining clip and removing the trim cover at the bottom of the steering column. Unfasten and take out the nuts on the intermediate shaft connecting piece, slide out the retaining plate and separate the halves of the intermediate shaft to obtain the connecting piece. Carefully remove the rubber boot off the steering gear, and now mark the association between the intermediate shaft universal joint and the steering gear drive pinion with a hammer and punch. Unscrew and loosen the pinch bolt which holds the joint in the pinion and hold the lower half of the intermediate shaft free of the steering gear and out of the car. Connect the position of the upper universal joint with the steering column, loosen and unscrew the clamp bolt and nut and part the upper half of the intermediate shaft with the column splines and detach it. Check the universal joints on the roughness and mobility; change the damaged joints and the shaft boot (where necessary). Make sure that the front wheels remain straight along and make sure that the steering wheel is firmly in place. Line up the marks created in the removing process to ensure that the upper half of the shaft is inserted in the steering column splines, fit the clamp bolt and screw in the new retaining nut to a given torque value. Put the rubber boot in place, put the lower half of the intermediate shaft into location and connect the steering gear pinion splines to it, installing the clamp bolt and tightening it to the required torque. Connect the connecting piece on the top half of the shaft, align the halves, and connect them with the connecting piece and put the retaining plate in place and tighten the new nuts to the desired torque level. Lastly, install the rubber boot in the firewall, fasten it to the steering gear with a new cable tie and reduce the car to the ground.

Genuine Volkswagen Steering Shaft

Steering Stem Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

30 Steering Shafts found

View related parts
Volkswagen Shaft Part Number: 251-419-753-C
$64.41 MSRP: $90.22
You Save: $25.81 (29%)
ADD TO CART
Product Specifications
- Other Name: Lower Shaft
Fits the following Volkswagen Models:
- Transporter | 1985-1987 | Base | 4 Cyl 1.9 L GAS, 4 Cyl 2.1 L GAS
- Vanagon | 1984-1991 | Base, Campmobile, Carat, GL, L, Syncro | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.9 L GAS, 4 Cyl 2.1 L GAS
View related parts
Volkswagen Intermediate Shaft Part Number: 1EB-419-753-J
$71.32 MSRP: $99.88
You Save: $28.56 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft
Fits the following Volkswagen Models:
- ID.4 | 2021-2022 | 1st Edition, Pro, Pro S | BATTERY EV (EV/BEV)
View related parts
Volkswagen Lower Shaft Part Number: 1EK-419-753
$94.24 MSRP: $131.99
You Save: $37.75 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft
Fits the following Volkswagen Models:
- ID.4 | 2023 | Pro, Pro S, Pro S Plus, S, Standard | BATTERY EV (EV/BEV)
View related parts
Volkswagen Steering Shaft Part Number: 701-419-505-F
$74.22 MSRP: $103.95
You Save: $29.73 (29%)
ADD TO CART
Product Specifications
- Other Name: Steer Column
Fits the following Volkswagen Models:
- EuroVan | 1997 | Camper | 6 Cyl 2.8 L GAS
View related parts
Volkswagen Intermediate Shaft Part Number: 7B0-419-951
$163.86 MSRP: $229.51
You Save: $65.65 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Lower Shaft
Fits the following Volkswagen Models:
- Routan | 2009-2014 | S, SE, SEL, SEL Premium | 6 Cyl 3.6 L FLEX, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Volkswagen Lower Shaft Part Number: 7D0-422-751-A
$160.65 MSRP: $225.00
You Save: $64.35 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft; Lower Shaft
Fits the following Volkswagen Models:
- EuroVan | 1999-2003 | GLS, MV | 6 Cyl 2.8 L GAS
View related parts
Volkswagen Joint Part Number: 1H0-419-951
$164.22 MSRP: $230.00
You Save: $65.78 (29%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Joint, Shaft Assembly
- Position: Lower
Fits the following Volkswagen Models:
- Cabrio | 1995-2002 | Base, GL, GLS, GLX, High Line | 4 Cyl 2.0 L GAS
- Golf | 1993-1999 | Base, Celebration Edition, City, CL, GL, GTI, GTI VR6, Jazz, K2, Limited Edition, Sport, TDI, Trek, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
- Jetta | 1993-1999 | Base, Celebration Edition, City, GL, GLS, GLX, GT, Jazz, K2, Limited Edition, TDI, Trek, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View More
View related parts
Volkswagen Shaft Part Number: 357-419-951-A
$186.35 MSRP: $261.00
You Save: $74.65 (29%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Lower Shaft, Shaft, Shaft Joint
Fits the following Volkswagen Models:
- Passat | 1990-1997 | CL, GL, GLS, GLX, TDI | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Shaft Part Number: 175-422-951
$192.07 MSRP: $269.00
You Save: $76.93 (29%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Lower Shaft
Fits the following Volkswagen Models:
- Jetta | 1984-1992 | Base, Carat, GL, GLI, GLI 16-Valve, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.7 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Shaft Part Number: 357-419-952-A
$227.30 MSRP: $318.35
You Save: $91.05 (29%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Lower Shaft, Shaft, Shaft Joint
Fits the following Volkswagen Models:
- Passat | 1990-1994 | CL, GL, GLX | 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Shaft Part Number: 176-422-951-B
$260.97 MSRP: $356.52
You Save: $95.55 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Drive Shaft
- Replaced by: 191-419-951-B
Fits the following Volkswagen Models:
- Golf | 1985-1990 | Base, GL, GT, GTI, GTI 16-Valve, GTI 8-Valve | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Shaft Part Number: 191-419-951-B
$260.97 MSRP: $356.52
You Save: $95.55 (27%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Lower Shaft, Steering Shaft
Fits the following Volkswagen Models:
- Golf | 1985-1992 | Base, GL, GT, GTI, GTI 16-Valve, GTI 8-Valve | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Jetta | 1985-1992 | Base, Carat, GL, GLI, GLI 16-Valve, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Shaft Part Number: 191-419-951-J
$269.23 MSRP: $367.80
You Save: $98.57 (27%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Lower Shaft, Steering Shaft
Fits the following Volkswagen Models:
- Cabriolet | 1985-1990 | Base, Bestseller, Boutique, Wolfsburg Edition | 4 Cyl 1.8 L GAS
- Golf | 1985-1992 | Base, GL, GT, GTI, GTI 16-Valve, GTI 8-Valve | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Jetta | 1984-1992 | Base, Carat, GL, GLI, GLI 16-Valve, Wolfsburg Edition | 4 Cyl 1.6 L DIESEL, 4 Cyl 1.7 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View More
View related parts
Volkswagen Intermed Shaft Part Number: 701-419-951
$275.96 MSRP: $377.00
You Save: $101.04 (27%)
ADD TO CART
Product Specifications
- Other Name: Shaft; Intermed Shaft
Fits the following Volkswagen Models:
- EuroVan | 1995, 1993 | Camper, CL, GL, MV | 5 Cyl 2.5 L GAS
View related parts
Volkswagen Joint Part Number: 1H1-419-952-B
$287.92 MSRP: $393.33
You Save: $105.41 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Joint, Shaft Assembly
- Position: Lower
Fits the following Volkswagen Models:
- Cabrio | 1995-2002 | Base, GL, GLS, GLX, High Line | 4 Cyl 2.0 L GAS
- Golf | 1993-1999 | Base, Celebration Edition, City, CL, GL, GTI, GTI VR6, Jazz, K2, Limited Edition, Sport, TDI, Trek, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
- Jetta | 1993-1999 | Base, Celebration Edition, City, GL, GLS, GLX, GT, Jazz, K2, Limited Edition, TDI, Trek, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View More
View related parts
Volkswagen Shaft Part Number: 175-422-951-A
$292.07 MSRP: $399.00
You Save: $106.93 (27%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Shaft
- Position: Lower
Fits the following Volkswagen Models:
- Cabriolet | 1985-1991 | Base, Bestseller, Boutique, Carat, Etienne Aigner, Wolfsburg Edition | 4 Cyl 1.8 L GAS
View related parts
Volkswagen Shaft & Joint Part Number: 357-419-952-E
$294.85 MSRP: $402.80
You Save: $107.95 (27%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Shaft Joint
- Position: Lower
Fits the following Volkswagen Models:
- Passat | 1994-1997 | GLS, GLX, TDI | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Shaft Part Number: 535-419-951-A
$300.94 MSRP: $411.12
You Save: $110.18 (27%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Lower Shaft, Shaft
- Position: Lower
Fits the following Volkswagen Models:
- Corrado | 1990-1992 | G60 | 4 Cyl 1.8 L GAS
View related parts
Volkswagen Lower Joint Part Number: 535-419-951-C
$321.35 MSRP: $439.00
You Save: $117.65 (27%)
ADD TO CART
Product Specifications
- Other Name: Drive Shaft; Lower Shaft
- Position: Lower
Fits the following Volkswagen Models:
- Corrado | 1992-1994 | SLC | 6 Cyl 2.8 L GAS
View related parts
Volkswagen Lower Shaft Part Number: 701-419-951-B
$327.20 MSRP: $447.00
You Save: $119.80 (27%)
ADD TO CART
Product Specifications
- Other Name: Shaft; Intermed Shaft
- Position: Lower
Fits the following Volkswagen Models:
- EuroVan | 1999-2000, 1997 | Camper, GLS, MV | 6 Cyl 2.8 L GAS

| Page 1 of 2 |Next >

1-20 of 30 Results

Volkswagen Steering Shaft

The Volkswagen Steering Shaft transforms simple inputs from the wrist into precise wheel direction to give every driver sharp control over the road. For over 80 years, VW has constructed automobiles whose friendly appearance and reliable engineering combine to create cars that started with the Beetle that taught the world a small car could be fun and tough at the same time. Today, the brand continues that spirit in compact hatchbacks and roomy SUVs and forward-looking electric models, all riding on clever MQB architecture that reduces weight and cost while maintaining build quality. Turbocharged TSI engines, crisp dual-clutch gearboxes, digital cockpits, and park assist features are testament to both VW's ability to cram smart tech into cars designed for daily commuting, and its foray into the ID family of electric cars signals quite a path ahead to electric cars that are cleaner to drive. That wide lineup has one crucial component in common, the Steering Shaft that forms the spine of the steering system. Running between wheel and rack, the second shaft in the assembly involves sturdy steel and precise splines so torque travels quickly without dead spots and a collapsible zone for crash energy absorption for added safety. Universal joints allow it to flex with suspension movement, which keeps it in direct feel in city traffic or on long highway curves, so every VW maintains confident handling that's on par with the brand's reputation for solid, no-nonsense driving fun.

Buying OEM parts is a smart move to keep your long-term repair costs low. These components are built to last because VW uses such strict factory standards. At VWPartsGiant.com, it is easy to find genuine Volkswagen Steering Shaft at prices that actually beat the competition. You get a real manufacturer's warranty with every single part, so you know your purchase is safe. Plus, forget about return headaches since our policy is easy and worry-free. We ship your order fast, too. If you have questions, our team of parts experts is ready to help. Why wait? Start shopping now!

Volkswagen Steering Shaft Parts and Q&A

Joint
1H0-419-951
Q: What steps are needed for installing new nuts on the steering shaft connecting piece retaining plate and clamp bolt nut on Volkswagen Cabrio?
A:
The installation will require new nuts on the intermediate shaft connecting piece that will retain the plate and a new clamp bolt nut. Start by chocking the back wheels, switching on the parking brake and lifting the front part of the car in the air using jack and supporting the vehicle on axle stands making the front wheels point in a straight direction. Disassemble the rubber boot of the firewall, the cable tie and the boot of the steering gear, sliding the boot downwards to get to the intermediate shaft. In the event of necessity, it is also possible to access it internally, prying out the retaining clip and removing the trim cover at the bottom of the steering column. Unfasten and take out the nuts on the intermediate shaft connecting piece, slide out the retaining plate and separate the halves of the intermediate shaft to obtain the connecting piece. Carefully remove the rubber boot off the steering gear, and now mark the association between the intermediate shaft universal joint and the steering gear drive pinion with a hammer and punch. Unscrew and loosen the pinch bolt which holds the joint in the pinion and hold the lower half of the intermediate shaft free of the steering gear and out of the car. Connect the position of the upper universal joint with the steering column, loosen and unscrew the clamp bolt and nut and part the upper half of the intermediate shaft with the column splines and detach it. Check the universal joints on the roughness and mobility; change the damaged joints and the shaft boot (where necessary). Make sure that the front wheels remain straight along and make sure that the steering wheel is firmly in place. Line up the marks created in the removing process to ensure that the upper half of the shaft is inserted in the steering column splines, fit the clamp bolt and screw in the new retaining nut to a given torque value. Put the rubber boot in place, put the lower half of the intermediate shaft into location and connect the steering gear pinion splines to it, installing the clamp bolt and tightening it to the required torque. Connect the connecting piece on the top half of the shaft, align the halves, and connect them with the connecting piece and put the retaining plate in place and tighten the new nuts to the desired torque level. Lastly, install the rubber boot in the firewall, fasten it to the steering gear with a new cable tie and reduce the car to the ground.