How should the hood be removed and installed properly on Volkswagen Jetta?

Removing and installing the hood is a tedious task and thus, there are no less than two individuals who should undertake the task. Start with blankets or pads over the cowl of the body and the fenders. To remove the harness/hoses, pry out and unconnect the harness/hoses on the bottom of the hood, pry the grommet out, and then pull the harness/hoses out of the hood. Using a permanent marker, make alignment marks around the hinge plates so that the installation is the same. Get an assistant to assist in the support of the hood and then remove the upper end of hood support strut where applicable. Take off the hinge to hood nuts and the hood can be removed and it is the same to put it back on. To adjust, the fore-and-aft and the side-to-side placement is performed by sliding the hood up and down in relation to the hinge plates by means of loosening the nuts. Unscrew the nuts and just move the hood into position little by little. Screw the hinge nuts and lower the hood slowly checking the alignment. To provide a flat hood that aligns with the fenders when closed, turn the hood bumpers inwards or outwards and to raise or lower the hood height, screw the bumpers inwards or outwards. The loosening of the nuts also allows the adjustment of the hood latch assembly or the safety lever up-and-down and side-to-side.

How should the hood be removed and installed safely and correctly on Volkswagen Passat?

The hood is heavy and somewhat awkward to remove and install, so at least two people should perform this procedure. Begin by using blankets or pads to cover the cowl area of the body and the fenders to protect the body and paint during the hood lift. Scribe alignment marks around the hinge plate to ensure proper alignment during installation, using a permanent-type felt-tip marker or a marking pen. Disconnect the windshield washer hoses from the jets at the rear of the hood and the underhood light if applicable. Have an assistant support the weight of the hood while detaching the upper end of the hood support strut. Remove the hinge-to-hood bolts and lift off the hood, with installation being the reverse of removal. For adjustment, fore-and-aft and side-to-side alignment of the hood can be achieved by moving it in relation to the hinge plates after loosening the bolts. Scribe or trace a line around the entire hinge plate to judge the amount of movement, then loosen the bolts and adjust the hood into the correct alignment, tightening the hinge bolts or nuts and carefully lowering the hood to check the alignment. Adjust the hood bumpers on the front edge so the hood is flush with the fenders when closed, and adjust the safety latch assembly up-and-down and side-to-side after loosening the nuts. Periodically lubricate the hood latch assembly and hinges with white lithium-base grease to prevent sticking and wear.

Genuine Volkswagen Hood

Engine Hood

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

44 Hoods found

View related parts
Volkswagen Hood Part Number: 3B0-823-031-K
$231.03 MSRP: $323.56
You Save: $92.53 (29%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Passat | 2001-2005 | GL, GL TDI, GLS, GLS 4 Motion, GLS TDI, GLX, GLX 4 Motion, W8 | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL, 6 Cyl 2.8 L GAS, 8 Cyl 4.0 L GAS
View related parts
Volkswagen Hood Part Number: 1C0-823-031-M
$235.81 MSRP: $330.26
You Save: $94.45 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 1C0-823-031-J, 1C0-823-031-F
Fits the following Volkswagen Models:
- Beetle | 1998-2005 | Base, GL, GLS, GLS TDI, GLX, Sport, TDI, Turbo S | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Hood Part Number: 3C0-823-031-B
$236.61 MSRP: $331.38
You Save: $94.77 (29%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Passat | 2006-2007 | 2.0T, 3.6, Value Edition, Wolfsburg Edition | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Hood Part Number: 3C0-823-031-A
$246.40 MSRP: $336.62
You Save: $90.22 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 3C0-823-031
Fits the following Volkswagen Models:
- Passat | 2006 | 2.0T, 3.6, Value Edition | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Hood Part Number: 3C0-823-031-C
$267.73 MSRP: $365.75
You Save: $98.02 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Passat | 2007-2010 | 2.0T, 3.6, Komfort, Lux, Turbo, Value Edition, VR6, Wolfsburg Edition | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Hood Part Number: 5G0-823-031-J
$298.74 MSRP: $408.12
You Save: $109.38 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- GTI | 2015-2021 | Autobahn, Rabbit Edition, S, SE, Sport | 4 Cyl 2.0 L GAS
- Golf | 2015-2021 | Base, Launch Edition, S, SE, SEL, TDI S, TDI SE, TDI SEL, TSi, Wolfsburg Edition | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL
- Golf Alltrack | 2017-2019 | S, SE, SEL | 4 Cyl 1.8 L GAS
- Golf R | 2015-2019 | Base | 4 Cyl 2.0 L GAS
- Golf SportWagen | 2015-2019 | Limited Edition, S, SE, SEL, TDI S, TDI SE, TDI SEL | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL
- e-Golf | 2015-2019 | Limited Edition, SE, SEL Premium | BATTERY EV (EV/BEV)
View More
View related parts
Volkswagen Hood Part Number: 5K0-823-031-G
$293.67 MSRP: $401.19
You Save: $107.52 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 5K0-823-031
Fits the following Volkswagen Models:
- GTI | 2010-2014 | Base, Driver's Edition, Wolfsburg Edition | 4 Cyl 2.0 L GAS
- Golf | 2010-2014 | Base, TDI | 4 Cyl 2.0 L DIESEL, 5 Cyl 2.5 L GAS
- Golf R | 2012-2013 | Base | 4 Cyl 2.0 L GAS
- Jetta | 2010-2014 | S, SE, SEL, TDI | 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS, 5 Cyl 2.5 L GAS
View More
View related parts
Volkswagen Hood Part Number: 1J5-823-031-B
$300.74 MSRP: $410.85
You Save: $110.11 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 1J5-823-031-A
Fits the following Volkswagen Models:
- Jetta | 1999-2005 | GL, GL TDI, GLI, GLS, GLS TDI, GLX, TDI, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Hood Part Number: 1K0-823-031-J
$374.05 MSRP: $511.00
You Save: $136.95 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 1K0-823-031-E, 1K0-823-031-G
Fits the following Volkswagen Models:
- GTI | 2006-2009 | Base, Fahrenheit | 4 Cyl 2.0 L GAS
- Jetta | 2005-2010 | 2.0T, 2.5, GL, GL TDI, GLI, GLS, GLS TDI, S, SE, SEL, TDI, TDI Cup Edition, Value Edition, Wolfsburg Edition | 4 Cyl 1.9 L DIESEL, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS, 5 Cyl 2.5 L GAS
- R32 | 2008 | Base | 6 Cyl 3.2 L GAS
- Rabbit | 2006-2009 | 2.5, S | 5 Cyl 2.5 L GAS
View More
View related parts
Volkswagen Hood Part Number: 5NN-823-031-B
$377.05 MSRP: $515.10
You Save: $138.05 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Tiguan | 2018-2024 | S, SE, SE R-Line Black, SEL, SEL Premium, SEL Premium R-Line, SEL R-Line, SEL R-Line Jet Black | 4 Cyl 2.0 L GAS
View related parts
Volkswagen Hood Part Number: 3B0-823-031-E
$370.15 MSRP: $505.66
You Save: $135.51 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Passat | 1998-2001 | 4 Motion, GLS, GLS 4 Motion, GLX, GLX 4 Motion | 4 Cyl 1.8 L GAS, 6 Cyl 2.8 L GAS
View related parts
Volkswagen Hood Part Number: 17A-823-031
$416.31 MSRP: $568.73
You Save: $152.42 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 17A-823-031-A
Fits the following Volkswagen Models:
- Jetta | 2019-2024 | GLI 35th Anniversary Edition, GLI Autobahn, GLI S, R-Line, S, SE, SEL, SEL Premium, Sport | 4 Cyl 1.4 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
View related parts
Volkswagen Hood Part Number: 5C5-823-031-A
$421.68 MSRP: $576.07
You Save: $154.39 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Beetle | 2012-2019 | #PinkBeetle, Base, Classic, Coast, Denim, Dune, Final Edition SE, Final Edition SEL, Fleet Edition, GSR, R-Line, R-Line S, R-Line SE, R-Line SEL, S, SE, SEL, TDI, Turbo, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS, 5 Cyl 2.5 L GAS
View related parts
Volkswagen Hood Part Number: 1Q0-823-031-J
$428.15 MSRP: $584.89
You Save: $156.74 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 1Q0-823-031-H
Fits the following Volkswagen Models:
- Eos | 2008-2016 | Executive, Final Edition, Komfort, Lux, Sport, Turbo, VR6 | 4 Cyl 2.0 L GAS, 6 Cyl 3.2 L GAS
View related parts
Volkswagen Hood Part Number: 1C0-823-031-L
$458.60 MSRP: $626.50
You Save: $167.90 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- Beetle | 2006-2010 | 2.5, Base, S, SE, TDI | 4 Cyl 1.9 L DIESEL, 5 Cyl 2.5 L GAS
View related parts
Volkswagen Hood Part Number: 5C6-823-031-E
$458.60 MSRP: $626.50
You Save: $167.90 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 5C6-823-031-A, 5C6-823-031-C, 5C6-823-031-D, 5C6-823-031-B
Fits the following Volkswagen Models:
- Jetta | 2011-2018 | Base, GLI, GLI SE, GLI SEL, Hybrid, Hybrid SE, Hybrid SEL, Hybrid SEL Premium, S, SE, SE Sport, SEL, SEL Premium, Sport, TDI, TDI Premium, TDI S, TDI SE, TDI SEL, Wolfsburg Edition | 4 Cyl 1.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS, 5 Cyl 2.5 L GAS
View related parts
Volkswagen Hood Part Number: 7B0-823-031-D
$483.12 MSRP: $660.00
You Save: $176.88 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 7B0-823-031-B, 7B0-823-031-C, 7B0-823-031-A, 7B0-823-031
Fits the following Volkswagen Models:
- Routan | 2009-2014 | S, SE, SEL, SEL Premium | 6 Cyl 3.6 L FLEX, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Volkswagen Hood Part Number: 561-823-031-E
$519.22 MSRP: $709.31
You Save: $190.09 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 561-823-031-D, 561-823-031-C, 561-823-031-B, 56D-823-031-A
Fits the following Volkswagen Models:
- Passat | 2012-2015 | Limited Edition, S, SE, SEL, SEL Premium, Sport, TDI SE, TDI SEL, TDI SEL Premium, Wolfsburg Edition | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL, 5 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Hood Part Number: 3C8-823-031-B
$527.77 MSRP: $721.00
You Save: $193.23 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 3C8-823-031-A
Fits the following Volkswagen Models:
- CC | 2009-2012 | Executive, Lux, Lux Limited, Lux Plus, Luxury, R-Line, Sport, VR6, VR6 4Motion, VR6 Sport | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Volkswagen Hood Part Number: 3C8-823-031-D
$535.53 MSRP: $731.60
You Save: $196.07 (27%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Volkswagen Models:
- CC | 2013-2017 | 4 Motion, Executive, Executive 4 Motion, Lux, R-Line, R-Line Executive, Sport, Sport Plus, Trend, V6 Executive 4Motion, VR6 4Motion Executive | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS

| Page 1 of 3 |Next >

1-20 of 44 Results

Volkswagen Hood

A total system failure could result from a malfunctioning Volkswagen Hood, reducing driving comfort and posing a danger. It is for this reason that you should conduct regular inspections and replace such components in good time to enable your car to run smoothly and safely. OEM (Original Equipment Manufacturer) Volkswagen Hoods are perfect for motorists because they are the best quality parts produced as per the manufacturer's specifications; hence, they perform well and are reliable too, thus helping to retain the car's initial functionality as well as safety features. At VWPartsGiant.com, our genuine Volkswagen Hood supply indicates how much we care about the health of your vehicle. Additionally, our stock is vast, so every product will be easily accessible to you for finding and swapping without fear of making mistakes. With our user-friendly online catalog, it takes no time to identify the right spare part. Therefore, convenience accompanies servicing or maintaining a motorcar. You can rely on our OEM Volkswagen Hood to sustain the performance of your automobile.

Volkswagen Hood Parts and Q&A

Hood
5C6-823-031-E
Q: How should the hood be removed and installed properly on Volkswagen Jetta?
A:
Removing and installing the hood is a tedious task and thus, there are no less than two individuals who should undertake the task. Start with blankets or pads over the cowl of the body and the fenders. To remove the harness/hoses, pry out and unconnect the harness/hoses on the bottom of the hood, pry the grommet out, and then pull the harness/hoses out of the hood. Using a permanent marker, make alignment marks around the hinge plates so that the installation is the same. Get an assistant to assist in the support of the hood and then remove the upper end of hood support strut where applicable. Take off the hinge to hood nuts and the hood can be removed and it is the same to put it back on. To adjust, the fore-and-aft and the side-to-side placement is performed by sliding the hood up and down in relation to the hinge plates by means of loosening the nuts. Unscrew the nuts and just move the hood into position little by little. Screw the hinge nuts and lower the hood slowly checking the alignment. To provide a flat hood that aligns with the fenders when closed, turn the hood bumpers inwards or outwards and to raise or lower the hood height, screw the bumpers inwards or outwards. The loosening of the nuts also allows the adjustment of the hood latch assembly or the safety lever up-and-down and side-to-side.
Hood
3B0-823-031-E
Q: How should the hood be removed and installed safely and correctly on Volkswagen Passat?
A:
The hood is heavy and somewhat awkward to remove and install, so at least two people should perform this procedure. Begin by using blankets or pads to cover the cowl area of the body and the fenders to protect the body and paint during the hood lift. Scribe alignment marks around the hinge plate to ensure proper alignment during installation, using a permanent-type felt-tip marker or a marking pen. Disconnect the windshield washer hoses from the jets at the rear of the hood and the underhood light if applicable. Have an assistant support the weight of the hood while detaching the upper end of the hood support strut. Remove the hinge-to-hood bolts and lift off the hood, with installation being the reverse of removal. For adjustment, fore-and-aft and side-to-side alignment of the hood can be achieved by moving it in relation to the hinge plates after loosening the bolts. Scribe or trace a line around the entire hinge plate to judge the amount of movement, then loosen the bolts and adjust the hood into the correct alignment, tightening the hinge bolts or nuts and carefully lowering the hood to check the alignment. Adjust the hood bumpers on the front edge so the hood is flush with the fenders when closed, and adjust the safety latch assembly up-and-down and side-to-side after loosening the nuts. Periodically lubricate the hood latch assembly and hinges with white lithium-base grease to prevent sticking and wear.